background image

Saito engines are guaranteed against
workmanship and manufacturing
defects for a period of 3 years from
the original date of purchase. This
warranty is limited to the original
purchaser of the engine and is not
transferable. Warranty repairs will
not cover:

• Normal engine wear
• Damage due to insufficient

maintenance

• Damage related to over-revving of

engine due to small prop size or
unreasonable use

• Rusted bearings
• Crash damage

• Damage due to use of improper fuel

and/or glow plug

• Damage due to lean runs, such as

rusted bearings, seized connecting
rod or piston, etc.

• Damage caused by foreign objects

(dirt or broken glow plug filaments)

• Damage caused by unreasonable

mounting or running conditions
(dust, insufficient cooling, improper
mounting, improper propeller size,
or lack of balancing, etc.)

• Damage due to improper

disassembly

• Modifications of any kind

W  A  R   R   A  N  T Y      &      R   E  P  A  I  R  S 

1 9

1. Ship your engine in its original box,
freight prepaid to:

Horizon Service Center
Attn: Saito Service

4105 Fieldstone Road
Champaign, IL 61822
Phone: (217) 355-9511

Include complete name and address
information inside the carton, as well
as clearly writing it on the outer
label/return address area.

2. Include a note containing a brief
summary of the difficulty and include
the following information:

• Nitro content and brand of fuel
• Propeller size and brand used
• Type of glow plug used
• Type of engine mount
• Approximately how much running

time the engine had before difficulty

Date your correspondence and be sure
your name and address appear on this
enclosure. Also, include a phone
number where you can be reached
during the business day.

If your engine needs repair, please do the following:

Consumer Warranty and Repair Policy

 Saito Single Cyl Manual 9-00  9/11/00  10:06 AM  Page 21

Summary of Contents for FA-30S (H)

























Reviews: