background image

Operation

WARNING: 

Read and understand the safety chapter before you

operate the product.

To use fuel

Fuel mixture ratio

The fuel mixture ratio for the gasoline and two-
cycle engine oil is 

25

:1 

To make the fuel mixture

1. Determine the correct quantity of gasoline

and engine oil (mixture ratio 

25

:1). Do not

make more than 30 days quantity of fuel
mixture. 

.

2. Add half of the gasoline quantity to a clean

fuel container with an antispill valve.

CAUTION: 

Do not use gasoline

with more than 10% ethanol
concentration (E10). This can
cause damage to the product.

5

UNLEADED GAS

2 CYCLE OIL

1 GALLON US

(3.8 LITERS)

5.

1

 FL. OZ.

(15

2

 ml) 

1 LITER

40 ml

WARNING:

Gasoline is extremely flammable. Ignited vapors may explode. Always stop the engine

and allow it to cool before filling the fuel tank. Do not smoke while filling the tank. Keep sparks and open
flames at a distance from the area.

WARNING:

Remove the fuel cap slowly to avoid injury from fuel spray. Never operate the unit without

the fuel cap securely in place.

CAUTION:

For proper engine operation and maximum reliability, pay strict attention to the oil and fuel

mixing instructions on the 2-cycle oil container. Using improperly mixed fuel can severely damage the engine.

WARNING:

Add fuel in a clean, well-ventilated outdoor area. Wipe up any spilled fuel immediately.

Avoid creating a source of ignition for spilt fuel. Do not start the engine until fuel vapors dissipate.

MIXING RATIO - 25:1

 

25

:1 

10

 

10

 

Gasoline

  

2-cycle oil

  

Fuel Tank

Chain oil tank 

Visible fuel tank

Summary of Contents for 6220G












Reviews: