13
5. INSTALLATION.
•
Read and respect the Safety Information, described
in chapter 2 of this document. Failure to obey some
of the instructions described in this manual can result in a
serious or very serious accident to persons in direct contact
or in the vicinity, as well as faults in the equipment and/or
loads connected to it.
•
In addition to the device’s own user manual, other
documents are supplied on the Cd-Rom or documentation
pen drive. Consult them and strictly follow the indicated
procedure.
•
Unless otherwise indicated, all actions, instructions,
guidelines and notes are applicable to the devices, whether
or not they form part of a parallel system.
5.1. reCepTion oF The deviCe.
•
pay attention to section 1.2.1. of the safety instructions
-ek266 * 08- in all matters relating to the handling, move-
ment and location of the unit.
•
Use the most suitable means to move the UpS while it is
packed, with a transpalet or forklift.
•
Any handling of the device must be carried out in accordance
with the weights shown in the technical specifications
according to the model, indicated in chapter ‘9. Annexes’.
5.1.1. reception, unpacking and contents.
•
Reception. Check that:
The data on the label affixed to the packaging
correspond to those specified in the order. once the
UpS is unpacked, check the previous data with those of
the equipment nameplate.
If there are discrepancies, file the disagreement as
soon as possible, citing the equipment manufacture
number and the delivery note references.
It has not suffered any mishaps during transportation
(packaging and impact indicator in perfect condition).
otherwise, follow the protocol indicated on the label
attached to the impact indicator, located on the
packaging.
•
Unpacking.
To check the contents, it will be necessary to remove
the packaging.
Complete the unpacking according to the
procedure of section 5.1.3. Content.
•
Content
0.7 to 3 kvA device:
–
1 UpS.
–
Quick guide on paper.
–
Information for warranty registration.
–
1 USb cable.
–
3 cables with IeC connectors for loads.
–
1 cable for the device’s AC power supply.
–
2 metal pieces for use as handles and screws for
installing the unit in a rack cabinet.
–
4 plastic pieces for use as a base to facilitate
the arrangement of the UpS as a tower (vertical
position).
optional battery module for 0.7 to 3 kvA UpS:
–
1 battery module.
–
Information for warranty registration.
–
2 metal pieces for use as handles and screws for
installing the unit in a rack cabinet.
–
2 plastic pieces to extend the base of the UpS and
enable the arrangement of the attached battery
module in its mounting as a tower.
–
1 cable for interconnecting the battery module and
UpS or other module.
4 to 10 kvA device:
–
1 UpS.
–
1 pdU module (power distribution unit).
–
Information for warranty registration.
–
2 metal pieces for use as handles and screws for
installing the UpS in a rack cabinet.
–
2 metal pieces for use as handles and screws for
installing the pdU in a rack cabinet.
–
1 metal piece and screws for mounting the pdU
attached to the UpS arranged as a tower.
–
1 USb cable.
–
4 plastic pieces for use as a base to facilitate
the arrangement of the UpS as a tower (vertical
position).
–
1 cable for connecting the communication bus.
Useful only for connection to a parallel device.
–
1 cable for connecting the current bus. Useful only
for connection to a parallel device.
–
1 cable for interconnecting the battery module and
UpS.
4 to 10 kvA battery module:
–
1 battery module.
–
Information for warranty registration.
–
2 metal pieces for use as handles and screws for
installing the unit in a rack cabinet.
–
2 plastic pieces to extend the base of the UpS and
enable the arrangement of the attached battery
module in its mounting as a tower.
–
1 cable for interconnecting the battery module and
another module.
•
once the reception is completed, it is advisable to re-pack
the UpS until it is put into service in order to protect it
against mechanical shock, dust, dirt, etc.
•
The packaging of the device consists of a wooden pallet,
cardboard or wooden box, depending on the item, expanded
polystyrene corners, polyethylene cover and strapping, all
of which are recyclable materials. when the packaging
requires disposal, it must be carried out in accordance with
current laws.
we recommend keeping it for at least 1 year.
5.1.2. storage.
•
The device should be stored in a dry, ventilated room and
protected from rain, dust, and water or chemical splashes. It
is advisable to keep each device and battery unit in its orig-
inal packaging, as it has been specifically designed to en-
sure maximum protection during transportation and storage.
•
For devices that contain pb-Ca batteries, the
charging times indicated in Tab. 2 of document
ek266*08, determined by the temperature to which they
SLC TWIN RT2
UnInTeRRUpTIbLe poweR SUppLy SySTemS (UpS)
USER MANUAL
