background image

16

INSTALLATION

5.9.  Additional battery installation 

setup 

1500/2000 VA and 3000 VA include external battery port 
that allow to provide additional battery runtime. 1500/2000 
VA model has no internal battery, and 3000 VA has de-
signed an internal battery inside the UPS. 

Connecting battery cable to external battery port 

may occur sparkle if adding up additional battery. 

Follow the procedure to install additional battery as below: 

5.9.1.  1500 / 2000 VA models 

There are two external battery ports for each side of UPS 
itself and battery pack.

1. 

Connect the battery cable to the external battery port 
of the rear of UPS.

2. 

Then connect the supplied battery cable from ex-
tended battery module to the external battery port of 
the rear of previous UPS.

3. 

If continuing to add up extended battery pack, repeat 
above steps. 

5.9.1.1.  Additional battery connection in 

rack form

Fig. 34. 

Rear view of the additional battery connection

5.9.1.2.  Additional battery connection in 

tower form

 

Fig. 35. 

Rear view of the additional battery connection

5.9.2.  3000 VA model

There is one external battery port for the UPS itself. 

1. 

Connect the supplied battery module cable from ex-
tended battery module to the external battery port of 
the rear of UPS.

2. 

If continuing to add up extended battery module, re-
peat above steps.

5.10.  Communication Ports

5.10.1.  RS232 + Optocouplers

Pin# Description

I/O

Function explanation

1

Low Battery

Output

Low Battery Output (*normally open, 

pull to Pin#5 when battery low alarm in 

battery mode)

2

TxD

Output

TxD

3

RxD

Input

RxD

4

DTR

Input

(tied to Pin#6)

5

Common

--

Common (tied to chassis)

6

DSR

Output

(tied to Pin#4)

7

RTS

Input

No connection

8

AC Fail

Output

AC Fail Output (**normally open, pull 

to Pin#5 when battery low alarm in 

battery mode)

Table 6. 

DB9 Female (RS232 + optocouplers)

5.10.2.  USB port: HID protocol

The USB and RS232 are unable to operate at the same 
time. Either only USB or DB9 can connect with RS-232 at 
one time, usually connecting with USB function is priority.

USER'S MANUAL

Summary of Contents for 750 VA

























Reviews: