51
7.3.5. Setting menu.
Click on the menu screen
to obtain the UPS data logger.
Use icons
or
scroll through the events.
Tab. 21 provides the complete list of all events that the UPS can
display on the log history screen.
When frequent repetitions of events are detected, it is recom-
mended to contact the
T.S.S.
or the distributor.
This menu is of great help to the
T.S.S.
when it comes to deter-
mining certain incidents and/or possible anomalies. The inter-
vention actions involving some events are exclusively reserved
for the
T.S.S.
or the distributor.
NO.
UPS events
1
Clear fault
2
Clear log
3
Load on the UPS
4
Load on the Bypass
5
No load
6
Quick-load battery
7
Floating battery
8
Battery in discharge
9
Connected battery
10
Battery is not connected
11
Manual bypass switch
"On"
12
Manual Bypass switch
"Off"
13
EPO
14
Lack of modules
15
Generator input (it is
necessary to configure a
digital input to detect this
signal)
16
Faulty input
17
Bypass sequence fault
18
Abnormal Bypass voltage
19
Bypass module fault
20
Bypass module overload
21
Time exceeded of the
overload Bypass module
22
Bypass frequency out of
range.
23
Bypass transfer number
exceeded
24
Short circuit at the output
25
Low battery (EOD)
26
Battery test ON
27
Battery test correct
28
Battery maintenance
29
Bat maintenance correct
30
Inserted module
31
Removal of the power
module
32
Rectifier fault
NO.
UPS events
33
Inverter fault
34
Rectifier overtemperature
35
Fan fault
36
Output overload
37
Inverter overload time
exceeded
38
Inverter overtemperature
39
Inhibited UPS
40
Manual transfer of static
bypass
41
Quit manual transfer of
static bypass
42
Battery low voltage
43
Wrong battery polarity
44
Inverter protection
45
Input neutral fault
46
Bypass fan fault
47
Manual shutdown
48
Manual quick charge
49
Manual floating charge
50
UPS blocked
51
Parallel cable fault
52
Loss of N + X redundancy
53
End of discharge system
inhibited
54
Battery test fault
55
Battery maintenance
fault
56
Ambient overtemperature
57
Rectifier bus CAN fault
58
Inverter bus CAN fault
59
Inverter bus CAN data
fault
60
Shared load fault
61
Synchronous pulse fault
62
Input voltage detector fault
63
Battery voltage detector
fault
64
Output voltage fault
65
Bypass voltage detector
fault
NO.
UPS events
66
Inverter IGBT fault
67
Air temperature exhausting
fault of a module
68
Unbalanced input current
69
DC bus overvoltage
70
Rectifier soft start fault
71
Connection relay fault
72
Short-circuit relay
73
PWM synchronous fault
74
Module in smart standby
75
Manual transfer to inverter
76
Input overcurrent time
exceeded
77
No input temperature probe
78
No output temperature
probe
79
Overtemperature of the
air inlet
80
Reset capacitor time
81
Reset fans’ time
82
Reset battery data logger
83
Reset time fans’ static
bypass
84
Battery overtemperature
85
Life cycle of the static
bypass fan worn
86
Life cycle of the capacitors
of the modules worn
87
Life cycle of the fan of the
power modules worn
88
Driver's Inverter IGBT
blocked
89
Batteries depleted
90
Bypass bus CAN fault
91
Life cycle of the particle
filter exhausted
92
Battery test fault
93
Stopping of the battery
test
94
Wave saved
95
Bypass bus CAN fault
96
Firmware fault
NO.
UPS events
97
System configuration fault
98
Static bypass
overtemperature
99
Duplicate ID modules
Tabla 21.
List of events.
EMi3
SERVOMOTOR VOLTAGE STABILISER
USER'S MANUAL
