- 54 -
8.- MISE EN MARCHE ET ARRÊT.
8.1.- Contrôles avant la mise en marche.
• Vérifier soigneusement que toutes les connexions ont été réalisées correctement et qu’elles sont suffisamment serrées,
suivant l’étiquetage de l’appareil et les instructions du chapitre 7.
• Vérifier que les interrupteurs magnétothermiques de l’
ASI
sont désactivés (position «OFF»).
• Mettre l’appareil sous tension en actionnant les protections du tableau de distribution de la ligne d’entrée (interrupteur
différentiel et magnétothermique ou magnétothermiques) sur la position «ON».
•
Procéder dans l’ordre indiqué pour la mise en marche aussi bien que pour l’arrêt de l’
ASI
.
8.2.- Mise en marche initiale ou après un arrêt complet.
• Actionner les interrupteurs magnétothermiques de batteries
(M2)
et d’entrée
(M1)
de l’
ASI
sur la position «ON». L’écran
(LCD)
s’allume et les ventilateurs se mettent en marche, de même que le chargeur de batteries.
•
Avant d’utiliser l’
ASI
pour la première fois ou après un arrêt prolongé de plus de 6 mois, il faut recharger les batteries
pendant au moins 8 heures. Attendre de l’avoir fait pour continuer la procédure de mise en marche.
• Enfoncer pendant au moins 3 secondes le touche
(ON/OFF)
du panneau de contrôle, le voyant
( )
s’allumera. Le système
réalisera un autotest interne; cela fait, l’inverseur de l’
ASI
se mettra en marche et fournira une tension de sortie.
N’importe quelle anomalie du réseau sera absorbée par l’appareil.
Pendant la mise en marche, l’écran
(LCD)
affiche le message «EN ATTENTE» et quand l’appareil fournit une tension de sortie,
le voyant
(
)
s’allume et l’écran
(LCD)
affiche le message «EN MARCHE».
• Actionner sur «ON» les protections de distribution de sortie, si vous en avez et mettre en marche les charges critiques à alimenter.
8.3.- Arrêt quotidien de l’ASI, arrêt de l’«inverseur».
• Arrêter les charges et enfoncer le touche
(ON/OFF)
pendant au moins 3 secondes, l’inverseur s’arrêtera.
• L’écran
(LCD)
affichera «EXTINCTION» pendant quelques secondes, puis il restera simplement allumé, avec les ventilateurs et
le chargeur en marche.
8.4.- Mise en marche quotidienne de l’ASI, mise en marche de l’«inverseur».
• Enfoncer pendant au moins 3 secondes le touche
(ON/OFF)
du panneau de contrôle. Le système réalisera un autotest
interne; cela fait, l’inverseur de l’
ASI
se mettra en marche et fournira une tension de sortie.
N’importe quelle anomalie du réseau sera absorbée par l’appareil.
Pendant la mise en marche, l’écran
(LCD)
affiche le message «EN ATTENTE» et quand l’appareil fournit une tension de sortie,
le voyant
(
)
s’allume et l’écran
(LCD)
affiche le message «EN MARCHE».
• Mettre en marche les charges critiques à alimenter.
Summary of Contents for SLC Link Series
