14
SALICRU
5. INSTALLATION.
•
Read and respect the Safety Information, described
in section 2 of this document. The fact of ignoring
any of the indications described in it, can cause serious ac-
cidents or very serious injuries to the persons in the vicini-
ties in direct contact, as well as damages to the equipment
and/or loads connected to itself.
•
A part from the own user's manual of the equipment, the
CD-ROM or Pen Drive contents other documents, which
have to consulted and followed strictly.
•
Unless otherwise indicated, any action, indications, notes
and other ones are applicable to the equipments, never
mind if they belong to a parallel system or not.
5.1. EQUIPMENT RECEPTION.
•
It is dangerous to handle the equipment over the pallet
with no caution, because it could tip over or cause se-
rious injuries to the operators due to the impact of the fall and/or
entrapment. Pay attention to section 1.2.1. from Safety Intruc-
tions -EK266*08- regarding handling, moving and location of the
equipment.
•
Use the most suitable medium to move the UPS meanwhile
it is still packaged, by means of pallet jack or forklift.
•
Any equipment handling will be done keeping in mind the
weights and technical features of the model, stated in sec-
tion «9. Annexes».
5.1.1. Reception, unpacking and contents.
•
Reception. Check the following:
Data in the labelling of the packaging are the same as
the stated in the purchase order. Once the UPS is un-
packed, check previous data with the nameplate of the
equipment.
In case of discrepancies, make the non-conformity as
soon as possible by quoting the serial number of the
equipment and the delivery note reference.
No damage during transport (packaging and impact in-
dicator correct).
Otherwise, follow the stated protocol in the labelling
beside the impact indicator, located in the packaging.
•
Unpacking.
To check the contents, the packaging must be removed.
Complete the unpacking procedure according to
section 5.1.3.
•
Contents.
The own equipment.
User's manual in IT support: [CD-ROM] or [Pen Drive].
1 communication cable.
2 cables for parallel connection, current bus and control
signal.
1 female connector to connect into the external EPO. It in-
cludes an isolated cable as a «bridge» mode to close the
circuit (already fitted in).
•
Once the reception is finalised, it is better to pack the UPS
again till its commissioning in order to protect it against pos-
sible mechanical impacts, dust, dirt, etc...
•
The equipment packaging has wooden pallet, cardboard
or wooden enclosure depending on the requirements, ex-
panded polystyrene corners, plastic bag and polyethylene
wrap, all of them are recyclable materials. When they has
to be disposed proceed in accordance with the laws in
force.
It is advised to keep the packaging, for 1 year at least.
5.1.2. Storage.
•
The storage of the equipment will be done in a dry and
cool room, protected from rain, dust, water jets or chemical
agents. It is advisable to keep each equipment and battery
unit inside their original packaging, because they have
been designed to assure the maximum protection during
transport and storage.
•
Those equipments, which include Pb-Ca batteries,
the recharging period of time according to the storage
temperature, stated in Tab. 2 from EK266*08 document, must
be respected. Otherwise the warranty will be cancelled.
•
After this period of time, connect the equipment with the
batteries unit,if any, and start it up according to the instruc-
tions described in this user's manual and charge them for
12 hours.
In parallel systems, to charge only the batteries, it is not needed
to make the connection among the equipments. Proceed as com-
plete single equipments to charge them.
•
Later on, shutdown the equipment, disconnect it and pack
the UPS and batteries in their original packaging again, by
writing down the new recharging battery date in any docu-
ment or over the own packaging as a record mode.
•
Do not store the devices, where the temperature exceeds
over 50º C or below –15º C, because the electrical features
of the batteries can be affected.
5.1.3. Unpacking.
•
The equipment packaging has wooden pallet, cardboard
or wooden enclosure depending on the requirements, ex-
panded polystyrene corners [EPS] or polyethylene foam
[EPE], plastic bag and polyethylene wrap, all of them are
recyclable materials. When they has to be disposed pro-
ceed in accordance with the laws in force.
It is advised to keep the packaging, in case it was to be
used in future.
•
Equipments with single phase input TWIN PRO2 or three
phase input TWIN/3 PRO2 up to 10 kVA.
To unpack the equipment follow the sequence from
figure 4 to 7 (cut the wraps of the cardboard enclosure
and remove it from the top as it was a cover or in case
of wooden packaging, dismantle it with the needed
tools; remove the corners and plastic bag. The UPS will
be naked over the pallet.
With the help of one or two people in each side of the
UPS, download it from the wooden pallet.
