12
SALICRU
5. INSTALLATION.
t
Read and respect the Safety Information described
in Chapter 2 of this document. Failure to obey some
of the instructions described in this manual can result in a
serious or very serious accident to persons in direct contact
or in the vicinity, as well as faults in the equipment and/or
loads connected to it.
5.1. RECEPTION OF THE DEVICE.
t
Pay attention to section 1.2.1. of the safety instructions
-EK266 * 08- in all matters relating to the handling,
movement and location of the unit.
t
Use the most appropriate means to move the UPS.
t
Any handling of the device must be carried out in accordance
with the weights shown in the technical specifications
according to the model, indicated in chapter ‘9. Annexes’.
5.1.1. Reception, unpacking and contents.
t
Reception. Check that:
The data on the label affixed to the packaging
correspond to those specified in the order. Once the
UPS is unpacked, check the previous data with those of
the equipment nameplate.
If there are discrepancies, file the disagreement as
soon as possible, citing the equipment manufacture
number and the delivery note references.
There is no damage to the packaging that may have
occurred during transportation.
If there is damage, notify the carrier and indicate so on
the delivery note, and, as soon as possible, inform the
supplier / distributor or, failing that, our firm.
t
Unpacking.
Remove the packaging to check the contents.
Complete the unpacking according to the
procedure in section 5.1.3.
t
Content.
Device:
–
1 UPS.
–
Quick guide on paper.
–
Information for warranty registration.
–
1 USB cable.
–
3 cables with IEC connectors for loads.
–
1 cable for the device’s AC power supply.
–
2 metal pieces for use as handles and screws for
installing the unit in a rack cabinet.
–
4 plastic pieces for use as a base to facilitate
the arrangement of the UPS as a tower (vertical
position).
Optional battery module:
–
1 battery module:
–
Information for warranty registration.
–
2 metal pieces for use as handles and screws for
installing the unit in a rack cabinet.
–
2 plastic pieces to extend the base of the UPS and
enable the arrangement of the attached battery
module in its mounting as a tower.
–
1 cable for interconnecting the battery module and
UPS or other module.
t
Once the reception is completed, it is advisable to re-pack
the UPS until it is put into service in order to protect it
against mechanical shock, dust, dirt, etc.
t
The packaging of the device consists of a cardboard or
wooden box, depending on the item, expanded polystyrene
corners, polyethylene cover and strapping, all of which are
recyclable materials. When the packaging requires disposal,
it must be carried out in accordance with current laws.
We recommend keeping it for at least 1 year.
5.1.2. Storage.
t
The device should be stored in a dry, ventilated room and
protected from rain, dust, and water or chemical splashes.
It is advisable to keep each device and battery unit in its
original packaging, as it has been specifically designed
to ensure maximum protection during transportation and
storage.
t
For devices that contain Pb-Ca batteries, the
charging times indicated in Tab. 2 of document
EK266*08, determined by the temperature to which they
are exposed, must be respected, otherwise the warranty
may be invalidated.
t
After this period, connect the device to the mains together
with the battery unit if applicable according to the instructions
described in this manual and charge for 12 hours.
t
Then disconnect and store the UPS and batteries in their
original packaging, noting the new date for recharging
the batteries on a document as a record or even on the
packaging itself.
t
Do not store the devices where the ambient temperature
exceeds 50ºC or drops below -20ºC, as this may cause
degradation of the electrical characteristics of the batteries.
5.1.3. Unpacking.
t
The packaging of the device consists of a cardboard box,
expanded polystyrene (EPS) or polyethylene foam (EPE)
corners, polyethylene cover and strapping, all of which are
recyclable materials; consequently, if it requires disposal,
it must be carried out in accordance with current laws. We
recommend keeping the packaging in case it needs to be
used in the future.
t
Proceed as follows:
Cut the straps around the cardboard box.
Remove the accessories (cables, brackets, etc.)
Remove the device or battery module from the box with
the help, if necessary, of a second person depending
on the weight of the model or using appropriate
mechanical means.
Remove the protective corners from the device and the
plastic bag.
Do not leave the plastic bag within the reach of
children to avoid danger of suffocation.
Inspect the device before proceeding and, in the event
of finding damage, contact the supplier / distributor or,
failing that, our firm.
YOUR CONNECTION TO SAFETY
Thiele KG
• V
orderer W
einberg 26 • D-71522 Backnang • T
el.: +49 (0)7191 3560-0
• Fax.: +49 (0)7191 3560-19
• info@thiele-kg.de
• www
.thiele-kg.de
Thiele KG
• V
orderer W
einberg 26 • D-71522 Backnang • T
el.: +49 (0)7191 3560-0
• Fax.: +49 (0)7191 3560-19
• info@thiele-kg.de
• www
.thiele-kg.de
YOUR CONNECTION TO SAFETY
klick to
www
u-s-v
YOUR CONNECTION TO SAFETY
klick to
www
ACDC-DCDC
YOUR CONNECTION TO SAFETY
klick to
www
SYSTEME
YOUR CONNECTION TO SAFETY
klick to
www
CONTACT
YOUR CONNECTION TO SAFETY
klick to
www
CALLBACK
