background image

26

SALICRU

8.  MAINTENANCE, WARRANTY AND SERVICE.

8.1. BATTERY 

MAINTENANCE.

 

t

Pay attention to all of the safety instructions concerning 
batteries indicated in section 1.2.3 of manual EK266*08.

 

t

The service life of the batteries greatly depends on the 
ambient temperature and other factors such as the number 
of charges and discharges, as well as their depth.
The service life is designed to be between 3 and 5 years if 
the ambient temperature  is between 10 and 20ºC. Different 
types of battery with different service lives are available 
upon request.

 

t

SPS.ADAVANCE RT2 series UPSs require minimum upkeep. 
The batteries used in the standard models are lead acid, 
sealed, valve regulated and maintenance free. The only 
requirement is to charge the batteries regularly to extend 
their life expectancy.
While it is connected to the mains supply, whether or not it 
is running, it will keep the batteries charged and also offer 
protection from overcharging and deep discharge.

8.1.1.  Notes for the installation and replacement of the battery. 

 

t

If it is necessary to replace any connection cables, original 
materials can be purchased through our 

T.S.S.

 or authorised 

distributors. Using inappropriate cables can lead to over-
heating in connections, which is a fire hazard.

 

t

Inside the device, there are permanent dangerous 
voltages even without mains supply present through 

its connection with the batteries and especially in UPSs 
where the electronics and batteries share a box.
Also take into consideration that the battery circuit is 
not isolated from the input voltage, so there is a risk of 
discharge with dangerous voltages between the battery 
terminals and the earth terminal, which is in turn connected 
to earth (any metal part of the device).

 

t

Repair and/or maintenance work must be carried out by our 

T.S.S.

, except for the replacement of batteries, which can 

be performed by qualified personnel familiar with them. No 
other person should handle them.
Depending on the configuration of the UPS, certain actions 
need to be carried out before handling the batteries:

 

ˆ

Devices with batteries and electronics sharing the 
same box.

 

Shut down the loads and device completely.

 

Disconnect the SPS.ADVANCE RT2 from the mains.

 

Open the device to access the interior.

 

Remove the fuse or internal battery fuses.

 

Release the battery holders and replace the 
batteries.

 

Perform the above steps in reverse to return the 
device to how it was at the start, including start-up.

 

ˆ

UPS with batteries and electronics in separate boxes.

 

Shut down the loads and device completely.

 

Disconnect the SPS.ADVANCE RT2 from the mains.

 

Disconnect the battery module from the UPS.

 

Open the battery module to access the interior.

 

Remove the fuse or internal battery fuses.

 

Release the battery holders and replace the batteries.

 

Perform the above steps in reverse to return the 
device to how it was at the start, including start-up.

8.2.  UPS TROUBLESHOOTING GUIDE.

If the UPS does not work properly, check the information shown 
on the LCD screen of the control panel and act accordingly 
depending on the device model.
Using the Tab. 14 troubleshooting guide, try to resolve the issue 
and, if it persists, consult our Technical Service and Support 

T.S.S.

If it is necessary to contact our Technical Service and Support 

T.S.S.

, provide the following information:

 

t

UPS model and serial number.

 

t

Date on which the issue occurred.

 

t

Full description of the issue, including information provided 
by the LCD display or LEDs and state of the alarm.

 

t

Power supply conditions, type of load and level of load 
applied to the UPS, ambient temperature, ventilation 
conditions.

 

t

Battery information (capacity and number of batteries), 
whether the device is a (B0) or (B1).

 

t

Any other information considered relevant.

 

t

Troubleshooting guide.

YOUR CONNECTION TO SAFETY

Thiele KG 

• V
orderer W

einberg 26 • D-71522 Backnang • T

el.: +49 (0)7191 3560-0 

• Fax.: +49 (0)7191 3560-19 

• info@thiele-kg.de 

• www

.thiele-kg.de

Thiele KG 

• V

orderer W

einberg 26 • D-71522 Backnang • T

el.: +49 (0)7191 3560-0 

• Fax.: +49 (0)7191 3560-19 

• info@thiele-kg.de 

• www

.thiele-kg.de

YOUR CONNECTION TO SAFETY

klick to

www

u-s-v

YOUR CONNECTION TO SAFETY

klick to

www

ACDC-DCDC

YOUR CONNECTION TO SAFETY

klick to

www

SYSTEME

YOUR CONNECTION TO SAFETY

klick to

www

CONTACT

YOUR CONNECTION TO SAFETY

klick to

www

CALLBACK

Summary of Contents for SPS.ADVANCE RT2
































Reviews: