8
SALICRU
5. INSTALLATION ANd OPERATION.
•
Read and respect the Safety Information, described
in chapter 2 of this document. failure to obey some
of the instructions described in this manual can result in a
serious or very serious accident to persons in direct contact
or in the vicinity, as well as faults in the equipment and/or
loads connected to it.
5.1. recePTion of The device.
5.1.1. reception, unpacking and contents.
•
Reception.
Check that the information on the label affixed to the
packaging matches that specified on the order. Re-
move the packing unit and check the above information
against that on the nameplate of the SPS.home.
If there are any discrepancies, report them, quoting the
references on the delivery note.
Check that no mishaps have occurred during transpor-
tation.
•
Unpacking.
The packaging consists of a full-colour cardboard box
with two moulded pieces of expanded polystyrene
(ePS) to protect the SPS.home from impacts.
•
Content.
device.
Quick guide.
warranty information.
Particular terms and conditions of warranty.
1 USb cable.
1 telephone/ASdL/modem cable.
•
After reception, it is advisable to store the device in its
original packaging as a preventative measure if installation
is not to be carried out immediately.
•
when the packaging needs to be disposed of, it must be
carried out in accordance with current laws.
we advise keeping it for at least 1 year.
5.2. siTing and consideraTions.
5.2.1. siting.
•
Install the unit in a location which takes into considera-
tion and complies with the Safety Instructions of document
ek266*08.
•
The UPS can be placed on a flat surface (on a table) or
mounted on a wall using the system located on the base
of the device.
5.2.2. considerations.
5.2.2.1. battery charging.
•
Although the unit’s internal battery is charged at the factory,
it may run down during transportation and/or storage, so it
should be charged for a minimum of 8 hours to ensure a full
charge before using the device with complete assurance.
Although the device can operate correctly without charging
the battery for the specified time, the risk of a prolonged
mains outage during the first hours of operation and the
UPS’s available backup time should be assessed.
•
To recharge the battery, simply leave the unit plugged
into an AC socket. The battery will charge irrespective of
whether the SPS.home is switched on or off.
5.2.2.2. Power connected to the SPS.home.
•
Check that the loads connected to the power sockets do
not exceed the power rating of the unit (see Section 7 of
this document).
If the rated capacities are exceeded, an overload condi-
tion will occur. If mains power is present, the input breaker
will trip and, in battery mode, the device’s inverter will be
blocked. either way, the end result will be an unwanted
stoppage of the device and loads.
•
for optimum performance, keep the load connected to the
SPS below 80% of rated capacity.
5.3. connecTion and commissioning.
•
All of the device’s connections, including those re-
lated to control, will be made with all of the
switches in standby and without mains power present (UPS
power supply line selector set to ‘off’).
•
It should never be forgotten that a UPS is a gener-
ator of electrical energy, so the user must take the
necessary precautions against direct or indirect contact
when it is part of the facility.
5.3.1. Procedure to follow.
observe the following order of operation and instructions:
1.
Plug the PC, screen and sensitive devices into the unit’s output
sockets
3
. Plug the modem and other non-sensitive and
low-consumption peripherals into the SPS.home’s output
sockets
4
.
do not plug
laser printers, paper shredders or other
high-consumption electrical devices or high current
probes into output sockets
4
and especially not into output
sockets
3
with backup. The power demand of any of these
devices will overload the SPS and possibly damage the
unit.
2.
Take power cable
1
and insert the plug into a properly con-
nected AC socket with an earth connection.
The socket that supplies power to the device must have a
properly connected earth cable
(
)
.
The SPS.home’s power socket will be protected by
a fuse or circuit breaker limiter. This line must not
power machines with large electrical demands such as air
conditioning units, refrigerators, etc.).
Avoid the use of extension cables, since the SPS itself
could be considered as a PdU.
3.
Press start-stop button
5
to start the unit. Its surrounding Led
will light up and the unit will emit a beep.
It is possible to start the unit without the presence
of mains power (Coldstart function) by pressing on
start-stop button
5
. This, however, is not recommended be-
cause if a mains failure extends beyond the available
backup, it will be necessary to carry out a forced stop.
In the event of a mains failure and the battery’s backup
