background image

Cleaning the machine

Training

Do not attempt to operate or complete any procedure on a machine unless you 
have received the appropriate training or read the instruction books.

To avoid the risk of RSI (Repetitive Strain Injury), place the machine on a surface 
which is ergonomically satisfactory to the user. Take frequent breaks during 
prolonged usage.

Sharp objects

Do not use sharp objects such as screwdrivers or long fingernails to operate the 
keys.

FCC and EMC declarations of compliance

United States

Canada

European Countries

Table 1.1  Cleaning DOs and DON’Ts

DO

DO NOT

Wipe down the outside of standard products 
with a clean cloth, moistened with water and 
a small amount of mild detergent

Attempt to clean the inside of the machine
Use harsh abrasives, solvents, scouring cleaners or 
alkaline cleaning solutions

Spray the cloth when using a proprietary 
cleaning fluid

Spray any liquid directly on to the display windows

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC 
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated 
in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and 
used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this 
equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the 
interference at his own expense.

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio 
Interference Regulations of the Canadian Department of Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils 
numériques de la Classe A prescrites dans le Règlement sur le brouillage radioélectrique edicté par le ministère des 
Communications du Canada.

WARNING:

 This is a Class A product. In a domestic environment, this product may cause radio interference in which the user 

may be required to take adequate measures.

Summary of Contents for B 130























Reviews: