background image

9

Counting Operation

Enter the counting mode by selecting PCS as the unit of measure. This is 
explained in the previous section. If your scale has no pieceweight in 
memory, the 

Count

 annunciator will flash. If you want to use this 

pieceweight, skip to step 3 below to count items.

If you need to establish a new pieceweight, start at step 1 below.

1.

While in the counting mode, press and hold the 

ZERO

 key until…

The word 

count

 appears briefly on the scale, then the 

Count

 

annunciator flashes and six zeroes appear on the display.

2.

Place a known number of items on the scale platform and press the 

TARE

 key…

Five zeroes appear on the display with the first one flashing. Use 
the 

F

 key and the 

TARE

 key to enter the number of items on the 

scale. 

For example: To enter 25, you must press the 

TARE

 key three 

times to move the flashing digit to the right three times, then enter 
2 and 5 so the display looks like this: 

00025

.

After the last digit is entered, the scale calculates the pieceweight 
and displays the count on the scale.

3.

You can now place other similar items on the scale and see the 
displayed counts. If you want to start counting other items with a 
different pieceweight, clear the scale platform and repeat steps 1 
and 2 above.

The minimum pieceweight is approximately 0.0011 pounds. This 
translates to maximum counts of aprroximately 900 pieces per pound of 
scale capacity.

A-oFF

A-oFF

 is the next menu item. Use this to enable or disable the auto-off 

function. Follow these steps to set this function:

1.

Press and hold the 

F

 key for three seconds to access the 

Configuration menu …

rAnGE

 is displayed.

2.

Press the 

F

 key twice…

A-oFF

 is displayed.

3.

Press the 

TARE

 key…

Current setting, 

on

 or 

oFF

, is displayed.

Summary of Contents for C3235

















Reviews: