background image

3

Appendix A: Specifications................................................................................................................ 18

Appendix B: Serial Port Information .................................................................................................. 18

Appendix C: Error Messages............................................................................................................. 19

C.1

Error Messages............................................................................................................. 19
C.1.1 Operator Errors................................................................................................ 19

Appendix D: Notes on Rechargeable Battery.................................................................................... 20

D.1

Overview ....................................................................................................................... 20

D.2

When to charge the internal battery.............................................................................. 20

D.3

How to charge the internal battery ................................................................................ 20

D.4

How long to charge the internal battery ........................................................................ 20

LIST OF FIGURES

1-1

PALLET RUNNER 3000 Front Panel ..................................................................................... 4

3-1

PALLET RUNNER 3000 Display Detail .................................................................................. 6

3-2

Function Keys Layout ............................................................................................................. 7

5-1

PALLET RUNNER 3000 Main Circuit Board Overview .......................................................... 10

5-2

User Menu Key Assignments ................................................................................................. 11

5-3

User Menu Chart .................................................................................................................... 12

6-1

Calibration Mode Key Assignments........................................................................................ 16

LIST OF TABLES

1-1

PALLET RUNNER 3000 Information...................................................................................... 4

3-1

PALLET RUNNER 3000 Annunciator Definitions ................................................................... 6

5-1

User Menu Chart .................................................................................................................... 12,13,14,15

Summary of Contents for PR-3000 Series





















Reviews: