background image

TROUBLESHOOTING GUIDE

10

Problem 
The unit fails to steam
or the light on the
On/Off Switch does not
illuminate.

Indicator light is illumi-
nated but the Steamer
fails to steam.

Water drips from Nozzle 

Excessive gurgling of
Hose and Steam Nozzle 

Steam is intermittent 

Cause
The steamer is not
plugged in or the 
household circuit 
breaker is tripped or 
the fuse in blown.

Mineral build-up in the
unit or the Water Tank is
empty.

Condensation in Hose

Condensation in Hose

Mineral build-up in 
the unit.

Solution
Plug into the electrical
outlet, reset the circuit
breaker or replace the
fuse. If you need assis-
tance contact a qualified
electrician.
Follow the ‘Removing
the Mineral Build-up’
procedure in the Care
and Cleaning section or
refill the Water Tank 

Extend the Hose vertically
and allow water to drain
back to Water Reservoir.

Some gurgling is a natural
effect of the steaming
process. For excessive
gurgling extend the
Hose vertically to allow
water to drain back into
the Water Reservoir.
It is normal for the unit
to periodically stop
steaming for a few 
seconds. If the steam
stays off for longer 
periods, follow the
Removing Mineral 
Build-up procedure in
the Care and Cleaning
section.

 4444_Booklet SF-407_ENG.qxd  7/7/08  10:57 AM  Page 10

Summary of Contents for CST1162












Reviews: