SAM4S ER-600 SERIES
4-1
4 Disassembly and Assembly
Caution
· Before installation, be sure to turn off the power switch.
· Use gloves to protect your hand from being cut by the angle and the chassis.
· Connect all the cables correctly. When connecting or disconnecting the cables, be careful not to apply
stress to the cables. (It may cause disconnection)
· Be careful not to bind the other cables and the POWER S/W together.
4 Disassembling
4-1 Ass’y Case Upper
1. Take off the WATER PROOF(A-2).
2. Remove the five screws(C-17) on the back of the CASE LOWER( C-16). Lifting up the ASS’Y CASE-UPPER(A)
with care, separate the harness of the ASS’Y MCR CARD READER(reference:A-7) and the KBD FPCS
(D-10 or E-5) of the ASS’Y KBD(D or E type) from the MAIN BOARD(C-6)(Page 8-3.8-5).
3. Turn back the ASS’Y CASE-UPPER (A), remove the five screws(A-5) and lift up the COVER KBD(A-4)
or ASS’Y KBD(D or E type).
4. Remove the five screws(A-6) and lift up the ASS’Y KBD (D or E type) (Page 8-3.8-5).
5. Remove the two screws(A-9) and lift up the ASS’Y MCR CARD READER(reference:A-7)
from the CASE UPPER(A-3).
6. Remove the four screws(A-10) and separated the BRKT MCR(A-8) from the MCR CARD READER(A-7).
When the ASS’Y CASE-UPPER (A) doesn’t have the MCR CARD READER(A-7), first follow the 1,2 and 3 like
above, and then Separated the COVER MCR(A-1) from the CASE UPPER(A-3).
4-2 Ass’y DISPLAY
1. Separate the harness of the ETC-DISPLAY(B-3) from the MAIN BOARD(C-6).
2. After removing the two screws(C-11), separate the COVER WIRE(C-10)
and then remove the CAP(B-8) and the screw(C-14).
3. Remove the two screws(B-6) and separate the COVER REAR LCD(B-7).
4. Remove the four screws(B-5) from the COVE FRONT LCD(B-2) and separate ETC-DISPLAY(B-3).
5. Separate the WINDOW LCD(B-1) from the COVER FRONT LCD(B-2).
4-3 Ass’y CASE LOWER
1. Remove the two screws(C-12) and separate the HINGE ASS’Y(C-13).
2. Remove the COVER CABLE(C-9) and separate the POWER CORD(C-7), then the POWER-SMPS(C-8).
3. Separate the harness of the POWER S/W(C-15) from the MAIN BOARD(C-6).
4. Separate the POWER S/W(C-15) from the CASE LOWER(C-16).
5. Separate the harness of the ASS’Y SWITCH ROTARY(reference:C-3) from the MAIN BOARD(C-6).
6. After removing the two screws(C-2), lift up the ASS’Y SWITCH ROTARY(reference:C-3).
Remove the two screws(C-1) and separate BRKT MODE(C-4) from the SWITCH ROTARY(C-3).
7. Remove the five screws(C-5) and separate the MAIN BOARD(C-6) from the CASE LOWER(C-16).
Note]
To assemble, reverse the procedure of disassembly.
Summary of Contents for ER-600
