background image

 

 

Instruction manual

 

Fodder wagons OptiFEED

 

 

23 

 

2.

 

With 24-month warranty, after 12 months it is required to carry out a technical inspection on 

charge. 

3.

 

The warranty does not cover: 

a)

 

mechanical damages to the device, 

b)

 

damages being result of fire, flooding, lightning or other natural hazards, 

c)

 

devices subjected to modifications, repairs or disassembly by an unauthorized service 

point, 

d)

 

normally wearing parts (knives, tires, etc.), 

4.

 

The warranty is void if non-genuine spare parts and working materials such as oils etc. have 

been used. 

5.

 

The warranty is provided by the dealer. 

 

NOTE: 
PLEASE  ASK  YOUR  DEALER  TO  COMPLETE  AND  RETURN  THE 
WARRANTY  CARD  WITH  DATE  AND  PLACE  OF  PURCHASE,  AND 
DEALER'S STAMP AND SIGNATURE. OTHERWISE YOU MAY LOSE 
YOUR WARRANTY RIGHTS. 

 

NOTE: 
TO  BE  DEEMED  JUSTIFIED  UNDER  THE  CONDITIONS  OF  THE 
WARRANTY  THE  CLAIM  SHOULD  BE  SUBMITTED  WITH 
ADDRESS,  PURCHASE  DATE  AND  PLACE,  TEDDER  TYPE,  AND 
INVOICE NO. 

 

NOTE: 
IF THE WARRANTY EXPIRES, REPAIRS CAN BE CARRIED OUT FOR 
EXTRA CHARGE BY AUTHORISED REPAIR SHOPS SUGGESTED BY 
THE  DEALER.  THE  DEALER  IS  OBLIGED  TO  PROVIDE  THE 
PURCHASER WITH SUCH INFORMATION. 

 

Summary of Contents for DUO 1200 S


























Reviews: