background image

 

OPERATOR’S MANUAL

 

TRAILED ROTARY TEDDER 

P10-1200

 

 

 

Hydraulic hoses should be periodically checked and if any damage occur or they expire, replace 
with new ones. Expiry period should not exceed 5 years. 

 

Never use scotch tape to repair hydraulic hoses. 

 

When connecting hydraulic hoses to t

ractor’s hydraulic connectors make sure, that either tractor’s 

or tedder’s hydraulic system is without pressure

 

When  operating  hydraulic  system,  always  wear  protective  gloves  and  glasses.  Leaking  under 
pressure hydraulic oil (16 MPa) may permeate through the skin and cause infection. If it happens, 
immediately visit a doctor. 

 

The tedder should be stored under roofed places and in the way that it will not harm people or 
animals. 

 

Do  not  leave  agricultural  machinery  on  slopes  or  other  descents  without  providing  protection 
against its free runaway. 

 

Due to risk of tipping, it is not permissible to fold rotors for work on cants (across the slope). Setting 
the machine should be performed on an even ground or upwards/down the slope. 

 

When operating over a stony field or nearby roads there exists a risk of throwing out stones or other 
objects, which may pose a danger for passing-by vehicles on the road or for passers-by. Therefore 
keep the safe distance.  

 

Rotating  spring  tines  and  other  rotary  elements  present  a  danger  to  health  and  life  of  persons 
present nearby the machine. Do not touch any moving machine parts.  

 

The operator is not allowed to leave the tractor while driving. 

 

Prior to approaching operation with the machine, make sure that all safety guards are not damaged 
and fitted in place.  

 

Check pressure in the machine's wheels regularly.  

 

In the event of any break in the equipment operation, turn off the drive. 

 

While making repairs the machine must be stopped. 

 

Prior to performing any maintenance works, assembly, disassembly, parking set the machine onto 
a stable ground and protect against unintentional shifting. 

 

When cleaning the machine, use personal protective equipment for health protection. 

 

In case of a fatal failure, stop the machine's drive, turn the tractor's engine off and take out the 
ignition key. Then call for technical service, and if an accident (in this case: road accident) occurs, 
respect first aid rules and contact responsible authorities.

 

 

Machine should be kept clean, so as to avoid danger of fire. 

 

 

4.2.

 

Qualifications of operator  

To provide safe machine operation each person being the machine operator must meet the following 
requirements: 

 

Operator should hold driving license, have ability to drive vehicles safely and know road traffic rules. 

 

Operator must be in proper physical condition to be able to operate the machine. 

 

Operator must not be under the influence of alcohol, drugs and medicines, which all have influence 
on vehicle driving and machine operation. 

 

Operator should be familiarized with this manual and follow its provisions. 

 

Operator should be familiar with working principles of both the vehicle and the machine, and be able 
to recognize and avoid hazards resulting from operation of the aggregate. 

 

Summary of Contents for P10-1200









































Reviews: