background image

  

Operator’s manual 

Twin-rotor rotary rake  

Z2-780; Z2-840

 

 

- 12 - 

 

never  operate  the  rake  under  influence  of  alcohol,  drugs,  or  strong medicine  that  impair  your 
attention, 

 

do not wear clothes or jewelry that are too loose or too tight. Too loose clothing or jewelry may 
be pulled in by the rotating parts of the rake, 

 

the rake should not be operated by children or by handicapped people, 

 

When describing residual risk, the rake is treated as a machine, that up to the moment of its putting 
in motion it had been designed and manufactured according to technology level actual till the day of 
rake’s manufacture. 

 

CAUTION: 

Despite following the specified instructions and prohibitions, residual risk is 
still present. 

4.8.5. Residual risk assessment 

Residual risk occurs from not complying with the instructions and safety precautions. Such risk can 
be minimized by doing the following: 

 

thorough familiarizing yourself with operator’s manual, 

 

allow no persons on the machine when operating, 

 

allow no persons within the rake operation range, 

 

adjust, maintain and lubricate the machine with the engine off, 

 

only skilled persons should perform repairs of the machine, 

 

children and strangers must keep away when the machine is operating. 

 

 

When the risk of exposing to noise cannot be avoided or eliminated by any group 
protective means or organization of work, employer (farmer) must: 

1)

 

provide  the  operator  with  individual  means  of  noise  protection,  if  the  noise 
level in work place exceeds 80 dB. 

2)

 

provide the operator with individual means of noise protection and supervise 
the correctness of its usage, if the noise level in work place reaches or exceeds 
85 dB. 

4.9.  Safety labels and their meaning 

Safety labels are critical to safe use of this rake. They must be read, understood and followed. 

Also, be sure that: 

 

All warning decals are clean and legible. 

 

All lost or damaged decals are replaced by ordering new decals from your dealer or supplier. 

 

All  persons  using  this  rake  have  read  the  section  of  this  manual  explaining  the  meanings  of 
these labels. 

 

All  spare  part  used  for  repair  of  the  rake  should  have  all  safety  labels  provided  by  the 
manufacturer. 

 

Summary of Contents for Z2-780













































Reviews: