background image

 

Pressure 

 

 The use of pressurized air and fluids (paints or solvents) presents 

risks for the user and the equipment. 

 

Never exceed the maximum working pressures of the  equipment, 
components and accessories. 

 

For all cleaning, inspection and maintenance operations on the 
equipment, it is imperative to follow the procedures for decompression, 
shutdown, locking of any residual pressure, elimination of residual static 
electricity charges and purging of fluids 

Surfaces, 

edges, 

corners 

 

  Some component surfaces may be hot during operation. Skin 

contact with hot surfaces causes severe skin burns.

 

 

  Handle open or sharp-edged components with care. Wear 

protective gloves.

 

Equipment 

modification 

 

Under no circumstances should this equipment be modified or used for 
purposes not intended. 

 

Parts and accessories must only be supplied or approved by 

 

SAMES KREMLIN

 

SAMES KREMLIN

  cannot be held responsible for personal injury as 

well as breakdowns and/or damage resulting from modifications to the 
equipment. 

 

Any modification of equipment made by the user and not authorized by 

SAMES KREMLIN

 will result in loss of certification.

 

Environment 

 

Environmental risks must be controlled as follows: 

-

 

Respect an average temperature of use of the equipment and products, 

which must be at least 5°C (41˚F), lower than the flash point of the products 

and within a range of 0 to 

40°C (32˚ to 104˚ F).

 

-

 

Ventilation of the area by forced extraction and supply of unpolluted air is 
mandatory during operation of the equipment and cleaning operations. 

-

 

Fragile parts of the installation, especially the flexible hoses, must be 
protected from  mechanical or thermal damage during production or 
maintenance.  

-

 

Wastes related to the operation or dismantling of the equipment must be 
treated in accordance with the applicable laws. 

-

 

 The noise level of our equipment is limited to a maximum. However, 

operators must be protected according to the overall noise level of the 
environment.  Depending on the operating conditions, the sound volume of 
the equipment may cause hearing

 

problems. Use hearing protection and 

take appropriate measures to reduce noise pollution. 

 

Dispose of packaging materials in an appropriate and environmentally 
friendly manner. 

Summary of Contents for 135756312
































Reviews: