background image

SAMES KREMLIN 

- 3 - 

N° :  578.001.130-UK-1804 

 

 

CAUTION! 

It is forbidden to use material containing high concentrations of halogenated hydrocarbon 

solvents with  

aluminium

  or 

zinc fillers 

.Non-compliance with the instructions may cause 

explosion risk causing serious or fatal injury. 

EQUIPMENT REQUIREMENTS 

 

Guards (motor cover, coupling shields, connectors,…) have been designed for 

a safe use of the equipment. 

The manufacturer will not be held responsible for bodily injury or failure 

and / or property damage due to destruction, the overshadowing or the 

partial or total removal of the guards. 

 

PUMP

 

 

 

Before carrying out any work, it is imperative to read and clearly understand the disassembly and 

reassembly instructions before servicing. The operator must understand the equipment and the 

safety instructions. These instructions are available in the equipment manuals. 
The air motor is designed to be mounted with a pump. Never modify any components or 

couplings. When operating, please keep hands away from moving parts. Before starting up the 

equipment, please read the PRESSURE RELIEF instructions. Please ensure that any relief or 

drain valves fitted are in good working order. 

 

HOSES

 

 

  Keep hoses out of circulation areas, moving parts or hot surfaces, 

  Never expose product hoses to temperature higher than + 60°C / 140° F or lower than 0°C 

/ 32° F, 

  Never pull or use the hoses to move the equipment, 

  Tighten all fittings as well as the hoses before operating the equipment, 

  Check the hoses regularly; change them if they are damaged, 

  Never exceed the maximum working pressure (MWP) indicated on the hose. 

USED PRODUCTS

 

 

Considering the wide variety of products that are available and  can be used in our equipment it is  

impossible to check and make recommendations for  all chemical data,regarding the risks of 

possible chemical attack and  their long term chemical reaction 
SAMES KREMLIN can not be held liable for :  

  compatibility of wetted parts, 

  risks to staff and the surroundings,  

  for worn or defective parts, for faulty equipment or units, or the qualitiy of final product. 

It is the responsibility of the user to know and prevent any possible risks such as toxic vapours, 

fires or explosions. He shall determine the risks of immediate reactions or pursuant to repeated 

exposures of the staff, 
SAMES KREMLIN shall not be liable for physical  injuries, direct or indirect material damages 

caused by the use of chemicals. 

Summary of Contents for AIRMIX ATX





































Reviews: