background image

KREMLIN REXSON

N° : 578.001.130-UK-1103

FIRE - EXPLOSION - SPARKS - STATIC ELECTRICITY HAZARDS

A poor earth connection, inadequate ventilation, sparks or static electricity can cause an
explosion or fire. to avoid these risks when using or servicing KREMLIN REXSON equi pment,
the following safety procedures must be followed :

ensure a good earth connection and ground the parts to be handled i.e. solvents,
materials, components and equipment,

ensure adequate ventilation,

keep working area clean and free from waste solvents, chemicals, or solid waste i.e.
rags, paper and empty chemicals drums,

never use electrical switches / power if in an atmosphere of volatile solvent vapour,

stop working immediately in case of electrical arcs,

never store chemicals and solvents in the working area.

use paint whose flash point is the highest possible to prevent from any formation of gas
and inflammable vapours (refer to materials' safety instructions),

install a cover on the drums to reduce the diffusion of gas and vapours in the
spraybooth.

TOXIC PRODUCT HAZARDS

Toxic products or vapours can cause severe injury not only though contact with the body, but
also if the products are ingested or inhaled. It is imperative :

to know the material products and their risks,

notified or hazardous materials must be stored in accordance with the regulations,

the material must be stored in an appropriate container, never place materials in a
container where there is a risk of spillage or leakage,

a procedure must be applied for the safe disposal of waste material. It must comply with
all prevailing regulations and legislations of the country where the equipment is to be
used,

protective

clothing

should

always

be

worn

in

compliance

with

the

material

manufacturers' recommendations,

depending on the application and chemical safety instructions, safety glasses, hearing
protective earplug, gloves, foot wear, protective masks and possible breathing
equipment should be worn to comply with the regulations (Refer to chapter "Safety
equipment of KREMLIN selection guide).

CAUTION!

It is forbidden to use material containing high concentrations of halogenated hydrocarbon
solvents with

aluminium

or

zinc fillers

.Non-compliance with the instructions may cause

explosion risk causing serious or fatal injury.

Summary of Contents for AIRMIX XCITE Light








































Reviews: