background image

 

23 

18

 

Warranty 

SAMES  KREMLIN

  grants  a  contractual  guarantee  to  the  customer  for  a  period  of 

twelve  (12)  months  from  the  notification  of  supply,  subject  to  compliance  with  the 
conditions of use specified in this technical manual.  

To  be  implemented,  a  written  guarantee  request  must  precisely  define  the 
malfunction  of  the  item;  the  defective  unit  or  parts  must  be  sent  with  the  request. 

Conditions  of  purchasing  by  the  customer  to 

SAMES  KREMLIN

  must  also  be 

included of the request.  

SAMES  KREMLIN

  will  accept  or  refuse  the  implementation  of  the  guarantee  only 

after  analysis  of  the  ‘defective’  item.  The  warranty  given  by 

SAMES  KREMLIN

  is 

limited to the replacement of the item in its entirely or the partial replacement of the 
defective component.  

SAMES KREMLIN

 only bears the cost of the parts needed to replace the defective 

material.  

No guarantee will be granted by 

SAMES KREMLIN

 for the following: 

-  For  defects  and  deteriorations  resuslting  from  abnormal  storage  and  /  or  storage 

conditions at the customer’s premises or for maintenance or use of the item that does 

not  comply  with  the  generally  accepted  procedures  or  that  does  not  comply  with 

the instructions in this technical manual given to the customer by 

SAMES KREMLIN

.  

- For defects and damage resulting from replacement parts that were not approved 

by 

SAMES KREMLIN

 or that have been modified by the customer, 

- For any damage resulting from negligence or a lack of supervision by the customer, 

-  In  case  of  normal  wear  of  the  item  and  /  or  its  components  or  in  case  of 
deterioration or accident resulting from faulty and / or abnormal use thereof. 

Summary of Contents for FStart P HVLP-12-XLva






























Reviews: