Version B June, 2020
33
MagnaRam-SK
7.2.4 Elevator Piston Assembly 62-3009-02
Item Qty.
Part No.
Description
Item Qty.
Part No.
Description
1
1
72-2998-01 Stop Tube, Bottom
6
1
72-2998-03 Stop Tube, Upper
2
1
360-086
Nylon Wear Strip ¾ x 1in.
7
1 82-5298-06
Lock
Washer
M24
3
1
350-430
O-Ring, Buna 5 x 5 ½ in.
8
1
82-5298-05 SHCS M24-3 x 80mm
4
1
82-0720-44 O-Ring Viton 1 ½ x 1 11/16”
9
1
72-2998-04 Piston Rod MagnaRam
5
1
72-2998-02 Piston, Magna-Ram
-
1
62-3393-01
MagnaRam. Cylinder
Repair Kit (Guide Bushing
and Piston kit for 1
cylinder).
-
1
62-3393-04
MagnaRam, Cylinder
Repair kit (Guide
Bushing and Piston kit
for 4 cylinders).
Dis-Assembly:
1. Remove O-Ring (3) and Wear Strip (2).
2. Remove SHCS (8) and pull Piston (5), to remove
O-ring (4).
Clean and inspect all parts.
Assembly:
1. Replace O-Rings (3,4), Lubricate.
2. Install Piston (5) over Rod (9).
3. Loctite 742 SHCS (8) and install Lock Washer
(7) and Stop Tube (1).
Torque to: 125 Lb-ft. (170Nm).
4. Lubricate Wear Strip (2) into Piston (5) groove
with PTFE Grease. #560-440-001.
Tip: The Grease will hold the Wear Strip in place.
5. Lubricate each cylinder with 90Wt. oil.
6. After installing each piston into the cylinder, pour
7oz. (207cc) of 90W oil on the top of each piston.
The Oil keeps the cylinder lubricated.
2
5
3
4
7
9
6
8
1
Lubricate with
Magnalube
560-440-001
PTFE Grease
Torque to: 125
Lb-Ft (170Nm)
Apply 242 Loctite
Thread Locker
Maintenance: Yearly
1. Depressurize air to elevator.
a. Open and remove Guide
Bushings Bleeder Valve
b. Add 4 Oz (207cc) of 90W oil
to
each
cylinder.
c. Replace Bleeder Valve.
2. Open bleeder valves on bottom of
air
cylinder.
a. Raise elevator to discharge
any water or contaminants.
b. Close bleeder valves.
To Remove/Install the Piston Assembly on the
elevator see section: 5.2.4 Removing/ Installing the
Elevator Piston Assembly.
Summary of Contents for Magna-Ram
