Operation
User’s manual — 2900453/2
7
EN
3.1
Preparation for operation
1)
Before turning on the machine, check the level of
detergent and rinse aid in the bottles.
2)
Open the door/dome and check that all compo
-
nents are in good condition and properly installed:
– Filters.
– Overflow.
– Washing arms (upper and lower).
3.2
Main operating elements
Fig. 2:
Control panel and buttons
Buttons
ON/OFF button
•
Main functions: Turns the machine on and off.
– With the machine in standby, the icon is on.
– With the machine turned on, the icon is off.
START button
•
Main functions:
– Start of the wash cycle.
– Confirmation of setting parameters.
– With the door open, activate the "auto start" option.
PROG button
•
Main functions: selection of the washing pro
-
gramme.
Indicator/warning icons
3.3
Turning the machine on.
1)
Press the
ON/OFF
button.
⇒
All icons light up simultaneously for 2
seconds.
⇒
Thermal lock
activated: when the power is turned off, the
icon
continues to flash for 2
seconds and then turns
off.
2)
The machine heats up the rinsing boiler and the tank one after
the other.
⇒
While the machine is filling with water, the
icon
flashes. The cycle CANNOT start until the set water level is
reached.
⇒
When the working level is reached, the machine closes the
water inlet by means of a pressure switch and one of the
cycle lights comes on. [
/b]
3)
The machine heats the rinsing boiler and the tank one after the
other.
⇒
While the machine is heating up, the
light flashes.
⇒
The machine is ready for use when the pre-set temperatures
are reached in the boiler (between 75
and 85
°C, depending
on the program) and in the tank (between 50 and 65
°C
depending on the configuration). At this point, the
light
on the control panel comes on.
⭆
The estimated time for this operation is approximately
30
minutes.
3.4
Main operation
3.4.1
Prewash
1)
Remove any remaining dirt and rinse the items
before putting them in the dishwasher.
2)
Place the items in the dishwasher basket.
3)
When the basket is full, open the door or dome of
the machine and insert the basket centred on the support rails.
3.4.2
Program selection
1)
To select the wash program that best suits the type of item you
want to wash, press the
PROG
button
.
2)
Select the type of wash cycle by pressing the PROG button
.
With each press, a different cycle is selected from the program
list [
/b]
1
ON/OFF
button
a
Machine status
2
START
button
b
Program/cycle
3
PROG
button
c
Auto start
d
Cycle phase: washing or rinsing
Icon
Indication/warning
In standby mode it is on, pressing the
ON/OFF
button
switches it off and starts the filling and heating sequence.
Machine ready. It switches on when the tank and boiler have
reached the setpoint temperature.
Heating the machine during preparation.
Thermal lock
: it
flashes when the boiler has not yet reached the setpoint tem
-
perature at the time of rinsing.
Washing process.
Rinsing process.
Auto start: if it is on, this option is active. When the option is
active, the machine starts the cycle automatically when the
door/dome is closed.
1
2
3
b
a
c
d
Icon
Description
Icon
Description
GLASSES Cycle
DISHES Cycle
AX-40]
JUGS Cycle
AX-50, AX-100]
PANS
Cycle
DRAIN Cycle
Summary of Contents for AX-50
