Sammic CA-2V, User Manual

- 

19 

-

EN

tripping the protections. If you consider there is an anomaly in the machine, 
contact Sammic’s authorised technical service.

INITIAL SETTINGS

The following parameters can be changed on the machine:

1- Language
2- Maintain cutter speed: If enabled, the initial cutter speed will be the one 
used last time.
3- Maintain FORCE CONTROL: FORCE CONTROL is always active. 
4- Maintain programme time: the change of time of a programme is perma-
nent.
5- Programmes (see section “Programmes”).
6- Factory settings: reset the machine to return it to its factory settings.

To change these settings:
- Switch on the machine and keep the PRESS button (15) pressed during 
the first three seconds. 
- Use the UP (11) or DOWN (12) buttons to move from one setting to another 
and choose the one you want to change with the START button (14). If you 
make a mistake, push the PRESS button (15) once to return to the previous 
level.
- On the next level, use the UP (11) or DOWN (12) buttons to move from one 
value to another and confirm with the START button (14). By accepting the 
change, the machine returns to the previous level. If you make a mistake, 
push the PRESS button (15) once to return to the previous level.

To exit the settings, push the PRESS button (15)..

CHANGE OF LANGUAGE

- Switch on the machine and keep the PRESS button (15) pressed during 
the first three seconds.
- Select LANGUAGE with the START button (14).
- Select the language using the UP (11) or DOWN (12) keys and select it with 
the START button (14).
- Press the PRESS button (15) twice to make the change.

MACHINE COUNTERS

Switch on the machine and keep the START button (14) pressed during 
the first three seconds: this will access the counters that record the level of 
machine usage. Pressing UP (11) and DOWN (12) displays the following::
0 HPOW: Hours connected to the power supply.
1 HCUT: Hours with the motor running in Cutter mode.
2 HCOR: Hours with the motor running in Vegetable Cutting mode. 
3 NARR: Number of motor starts.
4 NMTERM: Number of thermal manoeuvres of the motor 
5 NMCIER: Number of bayonet closing manoeuvres.
6 NMTAPA: Number of manoeuvres of the vegetable cutting lid.
7 NMPCA: Number of manoeuvres of the vegetable cutter plunger and the 
cutter lid.
Press and hold the Start/Stop button for 3 seconds to reset the counters.
TIMER (13): Turns on all the icons on the screen. 
BAJAR (12) The panel version is shown.
SUBIR (11) The program version is shown.

PROGRAMMES

CREATE A NEW PROGRAM

- Unplug the machine and wait 

20 seconds

 before reconnecting. 

- Plug in the machine and, within 3 seconds,  press and hold the PRESS 
button (15), which accesses the parameters menu.
- Use the UP keys (11) until you reach the 

PROGRAMMES

 parameter and 

press the 

START button (14)

 to access the creation or modification of a 

program.
- The programmes are called C1, C2, C3… and up to 9 programs can be 
configured (C9). Use the UP (11) or DOWN (12) keys to locate the program 
you want to create or modify (C1, C2, C3...).
- Once the program is located, press the START button (14) to start mod-
ifying it.
- Once you have accessed the program configuration:

- The screen shows in the upper left the name of the program (C1, C2, 

C3...) and the 

phase

 (1.2,3..) you are configuring. 

- To configure a 

phase

 press the START button (14).

• Find the 

function

 you want to programme (speed, pulse, …) with the 

UP (11) and DOWN (12) buttons. Access the selected function with the 
START button (14). The machine has the following functions:
• 

SPEED

. Select a speed and the time it will be running:

• Use the UP (11) and DOWN (12) buttons to select the working 

speed (it will be flashing) and press the START button (14) to set it.

• Determine how long you will work at that speed (it will be flashing). 

Use the UP (11) and DOWN (12) buttons to change the time and 
the START button (14) to set it.

• The configuration of the function has concluded. Press START (14) 

to start defining the next phase (1.2,3...).

• 

PRESS

. Select the number of pulses (one second cycles while run-

ning) to be performed. 
• The number of pulses will appear flashing. Use the UP (11) and 

DOWN (12) buttons to determine the pulses to be realized and the 
START button (14) to set it.

 • The configuration of the function has concluded. Press START (14) 

to start defining the next phase (1.2,3...).

• 

REST

. The machine will be stopped for the time you indicate.

• A  flashing  time  will  appear  on  the  display.  Use  the  UP  (11)  and 

DOWN (12) buttons to determine the stop time and the START 
button (14) to set it.

• The function is finished. Press START (14) to start defining the next 

phase (1.2,3...)

• 

PAUSE

 The machine will be stopped until the user presses the 

START button (14).
  • The  function  is  finished.  Press  START  (14)  to  start  defining  the 

next phase (1.2,3...).

• 

END

 Closes the program.

• To end the program:

 • Configure the last phase of the program and choose the 

END

 func-

tion.

  •  If  you  want  to  exit  the  machine  parameter  configuration,  push  the 

PRESS (15) twice until the 

SAMMIC

 symbol appears.

• To access the new program:

 • The new program can be accessed with the (DOWN) arrows 12. It 

will be configured with the chosen name (C1, C2, C3...). To run the 
program, press the START button (14).