background image

7

R. 09/20  855 867

 SAMOA Industrial, S.A. · Pol. Ind. Porceyo,  I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com

2020_09_24-12:30

EN

1. Close fluid valves.
2. Drain the fluid from inside the pump. Anticipate a drainage of fluid from 

inside the pump.

3. Loosen the screws to remove the directional valve. Take special care with 

the seals.

4. Remove the valve cover by loosening the screws with an Allen wrench. 

Take note of the orientation of the cap, as it is critical to replace it correctly 
during reassembly.

5. Install a new set of valves according to these assembly drawings. Ensure 

that the ball guides are assembled as shown in the figure on the left, and 
tighten the screws with a maximum torque (see “Exploded parts and 
spare parts of the pump” section).

6. Assemble the directional valve with being careful not to damage the 

O-rings and tighten the screws with a maximum torque of 44.25 lbf·in 
(5 N·m).

ATTENTION:  To avoid fluid restriction and leakages, follow the 
position of the ball checks guides in the figure above.

REPAIR AND MAINTENANCE PROCEDURES

BALL VALVES REPLACEMENT

AIR SENSOR (ONLY FOR MODELS WITH AIR VALVE)

The air sensors are on the inside part of the diaphragm covers. To access them, follow the procedure for “Replacing diaphragms”. 
Once removed the covers following procedure:
1. Remove the two screws that secure the air sensor to the top.
2. Remove all components of the sensor. Clean the area.
3. Introduce new components in the order shown.
4. Fit the cover on the pump and tighten the screws to the body of the pump. Maximum tightening torque (see torque indicated in the section “Exploded 

parts and spare parts of the pump”).

5. Fit the remaining components in reverse order.

4

2

3

1

DF

DC

Summary of Contents for DF50













Reviews: