SAMLEX AMERICA INC. | 69
APPENDIX A
4.8.2.13 PASSWORD DISABLE
(Table 4.7, Parameter Setup Screen No.13)
This parameter allows to disable/ enable Password (8052) to change the value of programmable parameter. Use of
Password is recommended because it prevents accidental/ un-intentional change of parameter setting. Default is
enabled (PASSWORD DISABLE set at option "0=No")
4.8.2.13.1 Programming Steps for Parameter "PASSWORD DISABLE"
Enter Key Up Key x 4 times Enter Key Up Key x 12 times Enter Key
A N Y O P E R A T I N G
M O D E S C R E E N
ð
S E L E C T G R O U P
C H A R G E C U R V E
ð
S E L E C T G R O U P
O T H E R F U N C T I O N
ð
P OW E R S A V I N G
0 = D i s a b l e
ð
P A S S WO R D D I S A B L E
0 = N o
ð
K E Y I N P A S S WO R D
0 0 0 0
Password 8052
See Section 4.3.1
ð
P A S S WO R D D I S A B L E
0 = N o
4.9 GROUP 6 PARAMETER SETUP: TIME SETTING
(Section 4.1, Fig 4.2, Group 6)
Please refer to Parameter "TIME SETTING" under Group 6 at Fig 4.2. Set up details are given below. The Date and Time
Format is Year/Month/Day Hour:Minute (24 hour clock):
4.9.1 Programming Steps for Parameter "TIME SETTING"
Enter Key Up Key x 5 times Enter Key
A N Y O P E R A T I N G
M O D E S C R E E N
ð
S E L E C T G R O U P
C H A R G E C U R V E
ð
S E L E C T G R O U P
T I M E S E T T I N G
ð
T I M E S E T T I N G
Y Y Y Y / MM / D D H H . M M
i
INFO
• Time can be programmed from Year 2000 to 2099 only.
• Month can be programmed from 01 to 12 only.
• Day can be programmed from 01 to 31 only.
• Hour can be programmed from 00 to 24 only.
• Minute can be programmed from 00 to 60 only.
• If the numbers Entered for Month, Day, Hour and Minute are not within the above ranges, message "OUT
OF RANGE!" will be displayed and the display screen will go back to the previously set time. Setting
procedure will have to be re-started.
4.10 GROUP 7 PARAMETER SETUP: STOP SD CARD
(Section 4.1, Fig 4.2, Group 7)
Please refer to Parameter "STOP SD CARD" under Group 7 at Fig 4.2. Please note that this set up is displayed / accessible
only when SD Card is inserted in the SD Card Slot (9, Fig 1.1a). Set up details are given below:
Once SD Card is being used, it should be removed/ejected only after the operation of the Card has been stopped as
shown below and mesage "Please remove SD Card" appears. If the SD card is not removed within 30 sec, it will reset.
After the card is removed, it reverts to the original operating screen.
4.10.1 Programming Steps for Parameter "STOP SD CARD"
Enter Key Up Key x 6 times Enter Key Up Key x 1 time Enter Key
A N Y O P E R A T I N G
M O D E S C R E E N
ð
S E L E C T G R O U P
C H A R G E C U R V E
ð
S E L E C T G R O U P
S T O P S D C A R D
ð
S T O P S D C A R D
0 = N o
ð
S T O P S D C A R D
1 = Y e s
ð
P L E A S E R E M O V E
T H E S D C A R D
If SD Card is not
removed within 30 sec,
the unit will reset
SECTION 4 |
Parameter Setup