background image

WARNING AND CAUTION 

- 4 - 

 

 

                                

                              

                                 

 

     

             

       

    

 

 

WARNING: 

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS MONITOR TO RAIN 

OR MOISTURE. 

 

HIGH VOLTAGE EXISTS ON THE CATHODE-RAY TUBE ANODE LEAD OF THIS 

MONITOR. BEFORE SERVICING, DETERMINE THE PRESENCE OF HIGH VOLTAGE 

BY CONNECTING THE H.V. METER BETWEEN THE ANODE OF CRT CAP AND 

CHASSIS ONLY. 

 

CAUTION:  

1. Keep monitor away from excessive dust, high temperature, moisture or direct 

    sunlight. 

 

2. Use well ventilated area and do not cover ventilation openings. 

 

3. Unauthorized modification to this equipment, substitution or the use of an 

    unshielded connecting cable may cause excessive interference. 

 
4. As an ENERGY STAR 

®

Partner, SAMPO CORPORATION has determined that this  

    product meets the ENERGY STAR

®

guidelines for energy efficiency .

 

 

5. If the picture display is in any way abnormal, disconnect from main power supply. 

Check and ensure the installation is correct. Then reconnect the main power 

supply. 

 

CAUTION  

RISK OF ELECTRIC SHOCK 

DO NOT OPEN

 

CAUTION: TO REDUCE THE RISK OF ELECTRIC 

SHOCK, DO NOT REMOVE COVER (OR REAR) 

DO USER SERVICEABLE PARTS INSIDE 

REFER SERVICING TO QUALIFIED PERSONNEL 

Summary of Contents for SME-32DL5




























Reviews: