background image

 24  

EB 8365 EN

Servicing explosion-protected devices

Servicing explosion-protected 

devices

If a part of the device on which the explosion 
protection is based needs to be serviced, the 
device must not be put back into operation 

until a qualified inspector has assessed it ac

-

cording to explosion protection require-

ments, has issued an inspection certificate or 

given the device a mark of conformity.

Inspection by a qualified inspector is not re

-

quired if the manufacturer performs a rou-
tine test on the device prior to putting it back 
into operation. Document the passing of the 
routine test by attaching a mark of conformi-
ty to the device.
Replace explosion-protected components on-
ly by original, routine-tested components 
provided by the manufacturer.
Devices that have already been used outside 
hazardous areas and are intended for future 
use inside hazardous areas must comply 
with the safety requirements placed on ser-
viced devices. Before being operated inside 
hazardous areas, test the devices according 

to the specifications for servicing explosion-

protected devices.

Maintenance and calibration

Interconnection with intrinsically safe circuits 
to check or calibrate the equipment inside or 
outside hazardous areas is to be performed 
only with intrinsically safe current/voltage 
calibrators and measuring instruments to 
rule out any damage to components relevant 
to explosion protection.

 

Î

Observe the maximum permissible val-

ues specified in the certificates for intrin

-

sically safe circuits.

Summary of Contents for 4746









































Reviews: