background image

7-4  

EB 9510 EN

Start-up and configuration

7.1.4  Setting the local power line frequency

The local power line frequency must be entered to be able to properly filter out any distur

-

bances which are transmitted over ground wires or external power supply units. The default 
power line frequency is 50 Hz.

The power line frequency can only be changed in the 

Specialist

 user level.

1.  Press   key (in start screen) to go to the main menu.

2.  Select Start-up (1) with   or 

 key and confirm with 

 key.

3.  Select power line frequency (1.6) with   or   key.

4.  Press 

 key to change the setting (50 Hz or 60 Hz).

7.1.5 

Performing option module settings

The settings of the option module parameters can be performed in the option module wizard 

or the device settings.
The option module parameters can only be changed in the 

Specialist

 user level.

1.  Press   key (in start screen) to go to the main menu.

2.  Select Device settings (2) with   or 

 key and confirm with 

 key.

3.  Select option modules (2.2) with   or 

 key and confirm with 

 key.

4.  Select the required slot (2.2.2 to 2.2.5) with   or 

 key and confirm with 

 key.

5. 

Perform settings: the parameters are listed in the Annex A (configuration instructions).

Summary of Contents for 5007-2 Series









































































Reviews: