background image

4

855 819  R. 03/12

Samson Corporation • One Samson Way • N.C. 28778 Swannanoa • Phone: 00 1 8286868511 • Fax: 00 1 8286868533

2012_03_06-17:30

Description

Directflo concept

Air operated double diaphragm pumps are air-powered, reciprocating positive displacement pumps with two pumping chambers. Two diaphragms, 
centrally located in the chambers, separate the compressed air (dry side) from the fluid being pumped (wet side). A shaft transmits the reciprocating 
motion  of  one  diaphragm  to  the  other.  A  directional  valve  alternatively  distributes  the  air  from  one  chamber  to  the  other;  thus  a  reciprocating 
movement of the diaphragms is created. With each stroke, fluid is discharged by one of the diaphragms whilst the opposite diaphragm sucks new 
fluid into the expanding chamber. Check valves, two on the discharge side and two on the suction side, control and direct the fluid flow.

Capacity curves

DF100

Temperature working range

Material

Temperature range

PTFE

5 ºC   -  105 ºC    /    41 ºF   -   221 ºF

NBR

10 ºC   -   80 ºC    /    50 ºF   -   176 ºF

Acetal

10 ºC   -   90 ºC    /    50 ºF   -   194 ºF

Hytrel®

10 ºC   -  90 ºC      /    50 ºF   -   194 ºF

Neopreno

-18 ºC   -   93 ºC    /    0 ºF   -   200 ºF

SANTROPRENE

TM

-29 ºC   -   135 ºC   /   -20 ºF   -   275 ºF

Viton®

-10 ºC  -  120 ºC  /  -4 ºF   -   248 ºF

Tested at room temperature, with water and flooded pump with 3.5 inches, (80 mm), positive suction head.

100 psi 

87 psi 

72.5 psi 

58 psi 

43.5 psi

87 psi

100 psi

 58 psi

 72.5 psi

 43.5 psi

Summary of Contents for DF100



























Reviews: