background image

5

Stage 212: Dual Handheld Wireless System

Important Safety Information

1.  Read these instructions.
2.  Keep these instructions.
3.  Heed all warnings.
4.  Follow all instructions.
5.  Do not use this apparatus near water.
6.  Clean only with dry cloth.
7.  Do not block any ventilation openings. Install in accordance with the manufacturer’s 

instructions.

8.  Do not install near any heat sources such as radiators, heat registers, stoves, or other 

apparatus (including amplifiers) that produce heat.

9.  Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug 

has two blades with one wider than the other. A grounding type plug has two blades and 
a third grounding prong. The wide blade or the third prong are provided for your safety. If 
the provided plug does not fit into your outlet, consult an electrician for replacement of the 
obsolete outlet.

10.  Protect the power cord from being walked on or pinched particularly at the plugs, 

convenience receptacles, and at the point where they exit from the apparatus.

11.  Only use attachments/accessories specified by the manufacturer.
12.  Use only with the cart, stand, tripod, bracket, or table specified by the 

manufacturer, or sold with the apparatus. When a cart is used, use caution 
when moving the cart/apparatus combination to avoid injury from tip-over.

13.  Unplug the apparatus during lightening storms, or when unused for long 

periods of time. 

14.  Refer all servicing to qualified personnel. Service is required when the apparatus has 

been damaged in any way, such as power supply cord or plug is damaged, liquid has been 
spilled or objects have fallen into the apparatus has been exposed to rain or moisture, does 
not operate normally, or has been dropped.

15.  This appliance shall not be exposed to dripping or splashing water and that no object filled 

with liquid such as vases shall be placed on the apparatus.

16.  Caution-to prevent electrical shock, match wide blade plug wide slot fully insert.
17.  Please keep a good ventilation environment around the entire unit.
18.  The direct plug-in adapter is used as disconnect device, the disconnect device shall 

remain readily operable.

19.  Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such 

as sunshine, fire or the like.

20.  The AC plug considered as disconnect device of adapter.

Summary of Contents for Stage 212

















Reviews: