134
EB 8384-6S EN
Annex
11.3 Code list
Code
no.
Parameter
– Readings/
values [default setting]
Description
Note: Codes marked with an asterisk (*) must be enabled with Code 3 prior to configuration.
0
Operating mode
[MAN]
Manual mode
AUTO Automatic mode
SAFE Fail-safe position
ESC
Cancel
Switchover from automatic to manual mode is bumpless.
Automatic mode only possible if positioner has been initialized.
Reading: Code 0, see section 6
1
Manual set point
(manual
w)
[0] to 100 % of the nominal
range
Adjust the manual set point with the rotary pushbutton. The current
travel/angle is displayed in % when the positioner is initialized. If
the positioner is not initialized, the position of the lever in relation
to the longitudinal axis is indicated in degrees (°).
Note:
can only be selected when Code 0 = MAN
2
Reading direction
1234,
1234
, ESC
The reading direction of the display is turned by 180°.
3
Enable configuration
[No], YES, ESC
Enables changing of data (automatically deactivated when the
rotary pushbutton has not been operated for 120 seconds). Codes
marked with an asterisk (*) can only be read and not overwritten
when their configuration is not enabled.
HART
blinks on the display when the on-site operation is locked
over HART
®
communication.
PST
is displayed when the on-site operation is locked by the time-
controlled partial stroke test.
In these cases, codes can only read over the SSP interface.
4* Pin position
[No], 17, 25, 35, 50, 70,
100, 200 mm, 90° with
rotary actuators, 300 mm
with piston actuators, ESC
When attaching the positioner to the control valve, the follower pin
must be inserted in the proper pin position on the lever depending
on the travel/angle.
For initialization using NOM (nominal range) or SUB (substitute
calibration), the pin position must be entered.
For initialization using MAX, MAN and MAN2, the pin position is
not required, however, it is required under Code 5 to display the
nominal range.
Summary of Contents for TROVIS SAFE 3730-6
