background image

XPDm Digital Wireless

Important Safety Information

CAUTION: TO REDUCE THE RISK OF 
ELECTRIC SHOCK, DO NOT REMOVE COVER 
(OR BACK). NO USER-SERVICEABLE PARTS 
INSIDE. REFER SERVICING TO QUALIFIED 
SERVICE PERSONNEL.

This lightning flash with arrowhead 
symbol within an equilateral 
triangle is intended to alert the user 
to the presence of non-insulated 

“dangerous voltage” within the product’s 
enclosure that may be of sufficient magnitude 
to constitute a risk of electric shock.

The exclamation point within an 
equilateral triangle is intended 
to alert the user to the presence 
of important operating and 

maintenance instructions in the literature 
accompanying the appliance.

ATTENTION

RISQUE D’ÉLECTROCUTION !

NE PAS OUVRIR !

WARNING

TO PREVENT FIRE OR SHOCK HAZARD. DO NOT USE THIS PLUG WITH AN EXTENSION 
CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED 
TO PREVENT BLADE EXPOSURE. TO PREVENT FIRE OR SHOCK HAZARD. DO NOT EXPOSE 
THIS APPLIANCE TO RAIN OR MOISTURE. TO PREVENT ELECTRICAL SHOCK, MATCH WIDE 
BLADE PLUG TO WIDE SLOT AND FULLY INSERT.

Copyright 2021, Samson Technologies Corp. v1.1

Samson Technologies Corp.
278-B Duffy Ave
Hicksville, NY 11801
www.samsontech.com

If you want to dispose this product, do not mix it with general household waste. There is 
a separate collection system for used electronic products in accordance with legislation 
that requires proper treatment, recovery and recycling.
Private households in the 28 member states of the EU, in Switzerland and Norway may 

return their used electronic products free of charge to designated collection facilities or to a 
retailer (if you purchase a similar new one).
For Countries not mentioned above, please contact your local authorities for a correct method of 
disposal.
By doing so you will ensure that your disposed product undergoes the necessary treatment, 
recovery and recycling and thus prevent potential negative effects on the environment and 
human health.
WARNING!

Risk of explosion if battery is replaced by an incorrect type.

Summary of Contents for XPD2m















Reviews: