English - 15
Configuring Network Connections after Initial Setup
If you did not configure the network connections during initial setup, you can configure them through the Network Settings
option in the Main menu.
Configuring a Wireless Network Connection
The instructions below are for wireless networks that use the Dynamic Host Configuration Protocol (DHCP) to configure
network connections automatically. Most wireless networks use DHCP. If your have a Static IP network, see the e-Manual for
configuration instructions.
To configure the network connection for a network that uses DHCP, follow these steps:
1.
Connect your TV to your network as shown in the illustration on page 7.
2.
Turn on your TV, press the
MENU
button on your remote, and the select
Network
ĺ
Network Settings
.
3.
Select
Start
, and then press
ENTER
E
button.
4.
The Network function searches for available wireless network. When done, it displays a list of the available networks.
5.
In the list of networks, press the
Ÿ
or
ź
button to select a network, select
Next
, and then press
ENTER
E
button.
✎
If you have a WPS(PBC) compatible router, select WPS(PBC) instead, press
ENTER
E
, and then follow the
directions on the screen. When done, go to Step 8.
6.
Enter your network security key or
WPS PIN
using the remote.
✎
Enter numbers by pressing the number buttons on your remote.
✎
Enter letters by selecting a letter using the
Ÿ
/
ź
/
Ż
/
Ź
buttons, and then pressing
ENTER
E
.
✎
To display capital letters (or redisplay small letters if capital letters are displayed), select
Shift
, and then press
ENTER
E
.
✎
To display symbols and punctuation, select
, and then press
ENTER
E
. To redisplay letters, select
Shift
, and
then press
ENTER
E
.
7.
When done, use the
Ÿ
/
ź
/
Ż
/
Ź
buttons to select
Next
if you have entered a security key or
WPS PIN
if you have
entered a
WPS PIN
, and then press
ENTER
E
.
8.
The TV checks the wireless connection. If the connection is successful, the “Wireless network and Internet connection
complete” message appears. The cursor jumps to
Next
. Press
ENTER
E
.
✎
For more detailed information, see “Setting the Wireless Network” in the e-Manual.
✎
If you want to configure the connection manually, select
IP Settings
on the Network Connection screen. Set
IP
Setting
to
Enter manually
, and then enter the
IP Address
,
Subnet Mask
,
Gateway
, and
DNS Server
manually.
Configuring a Wired Network Connection
Most home networks use the Dynamic Host Configuration Protocol (DHCP) to configure network connections. Home networks
that support DHCP automatically provide the IP address, subnet mask, gateway, and DNS values your TV needs to access
the Internet so you don’t have to enter them manually. If your have a Static IP network, see the e-Manual for configuration
instructions.
To configure the network connection for a wired network that uses DHCP, follow these steps:
1.
Connect your TV to your network as shown in one of the illustrations on page 8.
2.
Turn on your TV, press the
MENU
button on your remote, and then select
Network
ĺ
Network Settings
. The
Network
Settings
screen will appear.
3.
Select
Start
, and then press
ENTER
E
button.
4.
The Network Connection screen appears, and verifies the network connection. Network set up is complete.
✎
If your TV cannot acquire network connection values automatically or if you want to set the connection manually,
select
IP Settings
on the network test screen. Set
IP Setting
to
Enter manually
, and then enter the
IP Address
,
Subnet Mask
,
Gateway
, and
DNS Server
manually.
✎
For more detailed information, see “Setting the Wired Network” in the e-Manual.
