Samsung CLP-610 Series, User Manual

4

.3   

<Selecting and loading print media>

Media sizes supported in each mode

Guidelines for special print media

Mode

Size

Weight

Source

Single side 
printing

All sizes 
supported by 
the machine

All weights 
supported by 
the machine

• tray 1
• optional tray
• multi-purpose tray

Duplex 
printing

a

a. 75 to 105 g/m

2

 (20 ~ 28 lb bond) only, and this feature is supported in 

CLP-6xxND.

Letter, A4, 
Legal, Folio, 
Oficio

75 to 90 g/m

2

(20 to 24 lb 
bond)

• tray 1
• optional tray
• multi-purpose tray

Media type

Guidelines

Envelopes

• Successful printing on envelopes depends upon 

the quality of the envelopes. When selecting 
envelopes, consider the following factors:
-  Weight: The weight of the envelope paper 

should not exceed 90 g/m

2

 or jamming may 

occur.

-  Construction: Prior to printing, envelopes 

should lie flat with less than 6 mm curl, and 
should not contain air.

-  Condition: Envelopes should not be wrinkled, 

nicked, or otherwise damaged.

-  Temperature: You should use envelopes that 

are compatible with the heat and pressure of 
the machine during operation.

• Use only well-constructed envelopes with sharp 

and well creased folds.

• Do not use stamped envelopes.
• Do not use envelopes with clasps, snaps, 

windows, coated lining, self-adhesive seals, or 
other synthetic materials.

• Do not use damaged or poorly made envelopes.
• Be sure the seam at both ends of the envelope 

extends all the way to the corner of the 
envelope.

Acceptable

Unacceptable

• Envelopes with a peel-off adhesive strip or with 

more than one flap that folds over to seal must 
use adhesives compatible with the machine’s 
fusing temperature for 0.1 second. Check your 
machine’s specification to view the fusing 
temperature, see page 10.1. The extra flaps and 
strips might cause wrinkling, creasing, or jams, 
and may even damage the fuser.

• For the best print quality, position margins no 

closer than 15 mm from the edges of the 
envelope.

• Avoid printing over the area where the 

envelope’s seams meet.

Labels

• To avoid damaging the machine, use only labels 

designed for use in laser machines.

• When selecting labels, consider the following 

factors:
-  Adhesives: The adhesive material should be 

stable at your machine’s fusing temperature. 
Check your machine’s specification to view the 
fusing temperature, see page 10.1.

-  Arrangement: Only use labels with no 

exposed backing between them. Labels can 
peel off sheets that have spaces between the 
labels, causing serious jams.

-  Curl: Prior to printing, labels must lie flat with 

no more than 13 mm of curl in any direction.

-  Condition: Do not use labels with wrinkles, 

bubbles, or other indications of separation.

• Make sure that there is no exposed adhesive 

material between labels. Exposed areas can 
cause labels to peel off during printing, which 
can cause paper jams. Exposed adhesive can 
also cause damage to machine components.

• Do not run a sheet of labels through the machine 

more than once. The adhesive backing is 
designed for only a single pass through the 
machine.

• Do not use labels that are separating from the 

backing sheet or are wrinkled, bubbled, or 
otherwise damaged.

Card stock or 
custom-sized 
materials

• Do not print on media smaller than 76 mm wide 

or 356 mm long.

• In the software application, set margins at least 

6.4 mm away from the edges of the material.

Media type

Guidelines