background image

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to 
provide reasonable protection against harmful interference in a residential 
installation. This equipment generates, uses and can radiate radio frequency 
energy and, if not installed and used in accordance with the instructions, may 
cause harmful interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular installation. If this 
equipment does cause harmful interference to radio or television reception, which 
can be determined by turning the equipment off and on, the user is encouraged 
to try to correct the interference by one or more of the

 

following measures: 

• Reorient or relocate the receiving antenna. 
• Increase the separation between the equipment and receiver. 
• Connect the equipment into an outlet on a circuit different from that to which the 
receiver is connected. 
• Consult the dealer or an experienced radio/TV technician for help. 
The device and its antenna must not be co-located or operating in conjunction 
with any other antenna or transmitter. 
 
Industry Canada 
Operation is subject to the following two conditions: (1) This device may not 
cause interference and (2) This device must accept any interference, including 
interference that may cause undesired operation of the device. 
The term "IC:" before the certification/registration number only signifies that 
registration was performed based on a Declaration of Conformity indicating that 
Industry Canada technical specifications were met. It does not imply that Industry 
Canada approved the equipment. 

 
 
Bluetooth 

The 

Bluetooth®

 word mark and logos are owned by the Bluetooth SIG, Inc. and 

any use of such marks by GN Netcom is under license. Other trademarks and 
trade names are those of their respective owners. 
 
 
 

16  Warranty and parts replacement 

 
To be added by Samsung 
 

17  Glossary 

 

Bluetooth

 is a radio technology developed to connect devices, such as 

mobile phones and headsets, without wires or cords over a short distance 
of approximately 10 metres.  More information is available at 
www.bluetooth.com 

 

Summary of Contents for Corona III

















Reviews: