English - 2
7
7
MENU
Used to display the on-
screen menu or return to
the previous menu.
8
8
…
…
/
†
†
/
œ
œ
/
√
√
Used to control the
cursor in the menu.
9
9
P.SIZE
Used to change the
screen size.
0
0
DUAL
I
-
II
Used to select the
sound mode.
!
!
TURBO
Used to select the turbo
sound option.
@
@
S.MENU
Used to display the
sound menu.
#
#
PRE-CH
Used to switch
repeatedly between the
last two channels
displayed.
$
$
VIDEO
Used to display all of the
available video sources.
%
%
P
/
Used to display the next
or previous stored
channel.
^
^
INFO
Used to view the
channel information and
setting status you
selected.(Depending on
the model, the signal
strength symbol (
)
can be displayed.)
&
&
EXIT
Used to exit from any
display or return to
normal viewing.
*
*
ENTER
While using the on-
screen menus, press the
ENTER
button to
activate (or change) a
particular item.
(
(
SLEEP
Used to select a preset
time interval for
automatic shut off.
)
)
P.MODE
Used to select the
picture effect.
a
a
S.MODE
Used to select the
sound effect.
1
1
POWER
Used to switch the TV
on and off.
2
2
Numeric buttons
Used to select channels
directly.
3
3
-/--
Used to select a channel
numbered ten or over.
Press this button, then
“--” symbol is
displayed. Enter the
two-digit channel
number.
4
4
MUTE
Used to switch the
sound off temporarily. To
turn the sound back on,
press the
MUTE
, ,
or
button.
5
5
/
Used to increase or
decrease the volume.
6
6
TV
Used to return to the TV
mode when it is in
external input mode.
➢
Operation of remote control may be affected by bright
artificial light near to the TV.
Remote Control
(depending on the model)
Installing Batteries
Remove the cover. Install two AAA
size batteries, then replace the cover.
When the remote control does not operate normally, check
that the “+” and “-” ends of the batteries are inserted
correctly or the batteries are drained.
➢
Do not mix battery types, i.e. alkaline and manganese.
The mains lead is attached to the rear of the television.
1
Plug the mains lead into an appropriate socket.
➢
The main voltage is indicated on the rear of the
television and the frequency is 50 or 60Hz.
2
Press the
button (On/Off) on the front (or side) of the
television.
3
Press the
POWER
button on the remote control to
switch the television on. The programme that you were
watching last is re-selected automatically. If you have
not yet stored any channels, no clear picture appears.
Refer to “Channel - Auto Store” or “Channel - Manual
Store” on page 4.
➢
If the television is initially powered on, several basic
customer settings proceed automatically. Refer to
“Setup - Plug & Play” on page 3.
4
To switch the television off, press the
button (On/Off)
on the front (or side) of the television.
Switching the Television On and Off
The television can be placed in standby mode, in order to
reduce power consumption and wear of the cathode ray
tube. Standby mode can be useful when you wish to
interrupt viewing temporarily (during a meal, for example).
1
Press the
POWER
button on the remote control while
viewing.
The television is in standby mode.
2
To switch the television back on, simply press it again.
☛
Do not leave the television in standby mode for long
periods of time (when you are away on holiday, for
example). Turn the television off by pressing the
button (On/Off) on the front (or side) of the television. It
is best to unplug the set from the mains and aerial.
Placing the Television in Standby Mode
AA68-03582C_Eng 8/16/06 4:11 PM Page 2
