background image

English  7

Ins
talling the hob

Installing the hob

WARNING

Be sure the new appliance is installed and grounded only by qualified personnel.
Please observe this instruction. The warranty will not cover any damage that may 
occur as a result of improper installation.
Technical data is provided at the end of this manual.

Safety instructions for the installer

• 

With respect to fire protection, this appliance corresponds to EN 60335 - 2 - 6. 
This type of appliance may be installed with a high cupboard or wall on one side.

• 

Drawers may not be fitted underneath the hob.

• 

The installation must guarantee shock protection.

• 

The kitchen unit in which the appliance is fitted must satisfy the stability 
requirements of DIN 68930.

• 

For protection against moisture, all cut surfaces are to be sealed with a suitable 
sealant.

• 

On tiled work surfaces, the joints in the area where the hob sits must be 
completely filled with grout.

• 

On natural, artificial stone, or ceramic tops, the snap action springs must be 
bonded in place with a suitable artificial resin or mixed adhesive.

• 

Ensure that the seal is correctly seated against the work surface without any gaps. 
Additional silicon sealant must not be applied; this would make removal more 
difficult when servicing.

• 

The hob must be pressed out from below when removed.

Connecting to the outlet

Before connecting, check that the nominal voltage of the appliance, that is, the 
voltage stated on the rating plate, corresponds to the available supply voltage. The 
rating plate is located on the lower casing of the hob.

The heating element voltage is AC 230 V~. This appliance is equipped with a cord 

that includes a grounding wire and a grounding plug. The plug must be plugged 
into an outlet that is properly installed and grounded.

WARNING

Once the hob is connected to the mains supply, check that all cooking zones are 
ready for use by briefly switching each on in turn at the maximum setting with 
suit- able cookware.

NOTE

When the hob is powered on for the first time, all displays light and the child 
safety lock is activated.

CTR432NB02_XSP_DG68-00315C-00_EN.indd   7

2017-07-24     6:00:32

Summary of Contents for CTR432NB02





















Reviews: