background image

English  11

Hob use

Hob use

Initial cleaning

Wipe the ceramic glass surface with a damp cloth and ceramic cooktop glass 
cleaner.

WARNING

Do not use caustic or abrasive cleaners. The surface could be damaged.

Using suitable cookware

Better pans produce better results.

• 

You can recognise good pans by their bases. The base should be as thick and 
flat as possible.

• 

When buying new pans, pay particular attention to the diameter of the base. 
Manufacturers often give only the diameter of the upper rim.

• 

Pots with aluminium or copper bases can cause metallic discolouration on 
the ceramic glass surface. The discolouration is very difficult or impossible to 
remove.

• 

Do not use pans which have damaged bases with rough edges or burrs. 
Permanent scratching can occur if these pan are slid across the surface.

• 

When cold, pan bases are normally bowed slightly inwards (concave). They 
should never be bowed outwards (convex).

• 

If you wish to use a special type of pan, for example, a pressure cooker, a 
simmering pan, or a wok, please observe the manufacturer’s instructions.

Other reasons why a cooking zone will switch itself off

• 

All cooking zones will immediately switch themselves off if liquid boils over 
and lands on the control panel.

• 

The automatic shutoff will also be activated if you place a damp cloth on 
the control panel. In both of these instances, the appliance will need to be 
switched on again using the 

On/Off

   button after the liquid or the cloth has 

been removed.

Residual heat indicator

When an individual cooking zone or the hob is turned off, the presence of residual 
heat is shown with an   (for “hot”) in the digital display of the appropriate 
cooking zones. Even after the cooking zone has been switched off, the residual 
heat indicator goes out only after the cooking zone has cooled.
You can use the residual heat for thawing or keeping food warm.

WARNING

• 

As long as the residual heat indicator is illuminated, there is a risk of burns.

• 

If the power supply is interrupted, the   symbol will go out and information 
about residual heat will no longer be available. However, it may still be 
possible to burn yourself. This can be avoided by always taking care when 
near the hob.

CTR432NB02_XSP_DG68-00315C-00_EN.indd   11

2017-07-24     6:00:34

Summary of Contents for CTR432NB02





















Reviews: