12_
setting up
INSTALLING THE WATER LINE
Connecting the water line to the
Refrigerator.
There are several items that you need to purchase to
complete this connection. You may fi nd these items
sold as a kit at your local hardware store.
•
6.35mm compression
nut
•
copper tubing
•
plastic tubing
•
ferrule
Household water line
Household water line
Plastic tubing (A)
Plastic tubing (A)
(Supplied)
(Supplied)
Ferrule (Not
Ferrule (Not
supplied)
supplied)
Compression
Compression
nut (A) (1/4”)
nut (A) (1/4”)
(Supplied)
(Supplied)
Compression
Compression
fitting (Supplied)
fitting (Supplied)
Molded
Molded
end(Bulb)
end(Bulb)
Compression
Compression
nut (B) (1/4”)
nut (B) (1/4”)
(Not supplied)
(Not supplied)
or
or
Copper tubing
Copper tubing
(Not supplied)
(Not supplied)
Plastic tubing (B)
Plastic tubing (B)
(Not supplied)
(Not supplied)
Refrigerator
Refrigerator
1.
Slip the compression nut through the supplied
plastic tubing(A).
2.
Tighten the compression nut (A) onto the 6.35mm
compression fitting.
-
If you are using copper tubing, slip the
compression nut (B)(not included) and ferrule
(not included) on copper tubing (not included) as
shown.
-
If you are using plastic tubing (B), insert the
molded end(Bulb) of the plastic tubing (B)into
the compression fitting. Do not use without the
molded end(Bulb) of the plastic tubing (B).
3.
Tighten the compression nut (B)onto the
compression fitting. Do not over-tighten the
compression nut (B).
4.
Turn water on and check for any leakage.
Only connect the water line to a drinkable water
source. If you have to repair or disassemble the
water line, cut off 6.35mm of the plastic tubing to
make sure you get a snug, leak-free connection.
However, it does not sterilize or destroy
microorganisms. You may need to purchase a
water purifying system to do that. In order for the
ice-maker to operate properly, a water pressure of
138~862 Kpa is required.
Under normal conditions, a 170 cc (5.75 oz.) cup
can be fi lled in 10 seconds. If the Refrigerator
is installed in an area with low water pressure
(below 138Kpa), you can install a booster pump to
compensate for the low pressure.
Make sure the water storage tank inside the
Refrigerator is properly fi lled. To do this, press the
water dispenser lever until the water runs from the
water outlet.
Water line installation kits are available at extra cost
from your dealer.
We recommend using a water supply kit that
contains copper tubing.
The new hose-sets supplied with the
appliance are to be used and that old
hose-sets should not be reused.
Check the accessory list below.
Compression fitting
Compression nut
Connecting to the water supply line
1.
First, shut off the main water supply line and turn
the ice-maker off.
2.
Locate the nearest cold water drinking line.
3.
After connecting the water supply with water
filter, turn on water supply and Flush 3L through
filter before use (flush approximately 6 minutes).
Cold Water Line
Cold Water Line
Pipe clamp
Pipe clamp
Shut off valve
Shut off valve
Water line
Water line
installation
installation
kit
kit
DA99-03404D-11.indb 12
DA99-03404D-11.indb 12
2015. 5. 7.
8:10
2015. 5. 7.
8:10
