Samsung DCB-9401R, Instructions For Use Manual

GB-27

DCB-9401R

GB

GB-26

D

I

G

I

T

A

L

C

A

B

L

E

R

E

C

E

I

V

E

R

DCB-9401R

TECHNICAL SPECIFICATIONS

Power supply 

Type :

SMPS

Input voltage :

AC 100-240V~, 50/60 Hz

Fuse rating :

250 V/T1.6AH

Tuner & Demodulator

Input Frequency :                      

VHF,UHF BAND(50~870 MHz)

DEMODULATION :                         

QAM DVB-C

SYMBOL RATE :                          

MAX 7 Msps

Constellation :                        

16, 32, 64, 128, 256 QAM

CABLE OUT :                            

LOOPOUT FOR ANALOG RECEIVER

Video decoder

System decoding : 

MPEG 2 ISO/TEC 13818
(Transport Stream)

Profile and level : 

MPEG 2 MP@ML (4:2:2)

Data rate : 

1 ~ 15 Mb/s

Video formats : 

4:3 (normal) & 16:9 (widescreen)

Picture resolution : 

720(H) x 576(V) x 50 fields/sec

Audio Decoder

System decoding : 

MPEG 1 ISO/TEC 11172~3 layer I & II

Audio mode : 

MONO, DUAL, STEREO, JOINT STEREO

Sampling frequency : 

32, 44.1, 48 kHz

BASE-BAND AUDIO/VIDEO OUTPUT

VIDEO PAL
Interface : 

2 SCART (AV1, AV2)

Impedance : 

75

Ω

Output level :

1Vp-p

AUDIO Interface : 

SCART

Impedance : 

600 balance

Output level : 

2.0Vp-p max (controllable)

S/PDIF (Digital Audio Output)

MEMORY

Flash 2MB
SDRAM 8MB

PHISICAL SPECIFICATION

Size (W x D x H) 

233 x 176 x 38 mm

Weight (Net) 

0.95Kg

Problem

Possible cause

Solution of the problem

No display LED on

Power cord 

Power cord plug in correctly

the front panel;

not plugged in correctly

No power supply

No pictures on the screen 

Receiver in Standby mode;

Set receiver to “On”;

SCART not connected tightly

Check connection and correct;

to video output of television;
incorrect channel or video

Check channel and video output and  

output selected on television

correct (TV instruction manual)

No sound

Audio cord connected 

Check connection and correct;

incorrectly;
Loudness level = 0;

Increase loudness on television set;

Muting active

Press the MUTE key

Remote Control does not

incorrect operation;

Point remote control

operate directly

towards the Receiver.

Batteries dead or inserted

Replace batteries or insert correctly 

incorrectly

Poor picture quality

Signal strength to low

Check all wire connections. Check the

signal strength in 

the “Scanning” menu, correct 
alignment of your antenna

On-Screen Error Message

cable not connected or not 

Check connection and correct

“Searching for signal” 

tight

On-Screen Error Message

Channel lists not installed

Scan channels. Please go to Installation  

“Channel data does not 

menu

exist.”

On-Screen Error Messages:    Smartcard:

(depend on model)

“Please check the                   - not plugged in correctly;             Check the Smartcard.

Smartcard”;                          - not plugged in.                           “Insert the Smartcard.”

“Please insert the 

Smartcard”.

The device, packaging material (e.g. Styrofoam) and the batteries must never be disposed of with
household refuse. Please obtain appropriate information about the regulations in your community,
and dispose of all refuse in accordance with regulations at the separate locations provided. 

DISPOSAL

TROUBLESHOOTING

MF68-00340A_GB_1105  11/5/04  11:38 AM  Page 26