DCB-B260Z
DCB-B260Z
GB-29
GB-28
D
I
G
I
T
A
L
C
A
B
L
E
R
E
C
E
I
V
E
R
GB
Power supply
Type :
SMPS
Input Voltage :
AC 100 - 240V~, 50/60 Hz
Fuse rating :
250 V/T1.6 AH
Power Consumption :
Max. 10W
Stand by :
7W
Tuner & Demodulator
Input Frequency :
VHF,UHF BAND(50~870 MHz)
DEMODULATION :
QAM DVB-C
SYMBOL RATE :
MAX 7 Msps
Constellation :
16, 32, 64, 128, 256 QAM
CABLE OUT :
LOOPOUT FOR ANALOG RECEIVER
Video decoder
System decoding :
MPEG 2 ISO/IEC 13818
(Transport Stream)
Profile and level :
MPEG 2 MP@ML (4:2:2)
Data rate :
1~ 15 Mb/s
Video formats :
4:3 (normal) & 16:9 (widescreen)
Picture resolution :
720(H) x 576(V) x 50 fields/sec
Audio Decoder
System decoding :
MPEG 1 ISO/IEC 11172~3 layer I & II
Audio mode :
single channel, dual channel, stereo,
joint stereo
Sampling frequency :
32, 44.1, 48 KHz
N
No
otte
e
:
The specification of the STB may be changed without notice in advance.
TECHNICAL SPECIFICATIONS
TROUBLESHOOTING
Problem
Possible cause
Solution of the problem
No display LED on
Power cord
Power cord plug in correctly
the front panel;
not plugged in correctly
No power supply
No pictures on the screen
Receiver in Standby mode;
Set receiver to “On”;
SCART not connected tightly
Check connection and correct;
to video output of television;
incorrect channel or video
Check channel and video output and
output selected on television
correct (TV instruction manual)
No sound
Audio cord connected
Check connection and correct;
incorrectly;
Volume level = 0;
Increase volume on television set;
Muting active
Press the MUTE key
Remote Control does not
Batteries dead or inserted
Point remote control towards the
operate directly
incorrectly
Receiver.
Replace batteries or insert correctly
Poor picture quality
Signal strength too low
Check the signal strength in
the “Installation” menu, correct
alignment of your signal cable
On-Screen Error Message
Antenna cable not connected
Check connection and correct;
“Searching for signal”
or not tight;
incorrect position of the
Check position and correct,
signal;
Check the signal strength in
the “Installation” menu
On-Screen Error Message
Receiver not yet set
Scanning of in “Installation” menu
“Channel data does not
exist.”
On-Screen Error Messages: Smartcard:
(depend on model)
“Please check the - not plugged in correctly; Check the Smartcard.
Smartcard”; - not plugged in. “Insert the Smartcard.”
“Please insert the
Smartcard”.
On-Screen Error Messages: No access to this channel
Check that you subscribe to this channel.
“No access”
If the STB has been switched off for a
longer period of time, turn on the STB,
select any channel, and wait for
authorization for up to 60 minutes.
The device, packaging material (e.g. Styrofoam) and the batteries must never be disposed
of with household refuse.
Please obtain appropriate information about the regulations in your community, and dispose
of all refuse in accordance with regulations at the separate locations provided.
DISPOSAL
MF68-00400A_GB 3/29/06 11:16 AM Page 28
Summary of Contents for DCB-B260Z
Page 2: ...Bruksanvisning SWE Instructions for use GB DCB B260Z 0A_3 4 SWE GB 3 29 06 11 16 AM Page II ...
Page 3: ...SWE DCB B260Z MOTTAGARE FÖR DIGITAL KABEL TV Bruksanvisning 0A_SWE 3 29 06 11 17 AM Page II ...
Page 19: ...DIGITAL CABLE RECEIVER Instructions foruse GB DCB B260Z 0A_GB 3 29 06 11 16 AM Page II ...
