44
45
GB
GB
Using the TV Buttons on the Remote Control
Your DVD-VCR remote control will work with Samsung
televisions and compatible brands.
To determine whether your television is compatible, follow the
instructions below.
1
Switch your television on.
2
Point the remote control towards the television.
3
Hold down the TV button and enter the two-figure code
corresponding to the brand of your television, by pressing the
appropriate numeric buttons.
Brand
Codes
Brand
Codes
SAMSUNG
01 to 06
PHILIPS
02, 20, 22
AKAI
09, 23
SABA
13, 14, 22 to 24
GRUNDIG
09, 17, 21
SONY
15, 16
LOEWE
02
THOMSON
13, 14, 24
PANASONIC
08, 23 to 27
TOSHIBA
07, 16 to 19, 21
Result:
If your television is compatible with the remote control,
it will switch off. It is now programmed to operate with
the remote control.
➢
If several codes are indicated for your television brand, try
each one in turn until you find one that works.
☛
When you change the batteries in the remote control, you
must reprogramme the code, following the same
procedure.
You can then control the television using the following buttons.
Button
Function
STANDBY/ON
➀
Used to switch the television and DVD-VCR on and off.
TV or VCR
➁
Used to switch between the TV and VCR modes.
INPUT SEL.
➂
Used to select an external source.
VOL
+
or
–
➃
Used to adjust the volume of the television.
PROG/TRK
➄
Used to select the required programme.
(
or
)
TV MUTE
➅
Used to mute the volume of the television.
➢
The various functions will not necessarily work on all
televisions. If you encounter problems, operate the
television directly.
OPEN/CLOSE
STANDBY/ON
1
2
2
5
5
4
4
3
6
Using the Assemble Edit Function
Recoding from Another VCR or Camcorder
This function allows you to start a new recording at a specific
position on the cassette while maintaining a very smooth scene
change.
1
Insert the cassette to be edited in your DVD-VCR.
2
Press the
❿
ll button to start playback.
3
When you reach the position from which you wish to start the
new recording, press the
❿
ll button.
4
Press the F.ADV/STEP (
) button again as often as
necessary to advance frame by frame, until the exact recording
position is located.
5
While the DVD-VCR is in still mode, hold the REC button (
●
)
down for a while to activate the Assemble Edit function.
6
Select the source from which you wish to record by pressing:
◆
The PROG ( or ) buttons for television channels
◆
The INPUT SEL. button for the LINE input sources
7
Press the
❿
ll button to start recording.
8
When you have finished recording, press
■
.
OK
2
5
4
You can copy a cassette to your DVD-VCR from another video
source, such as another VCR or a camcorder.
☛
It is an infringement of copyright laws to copy
prerecorded cassettes or to re-record them in any form
without the permission of the owners of the
corresponding copyright.
1
Connect the DVD-VCR, from which the cassette is to be copied,
to the appropriate RCA audio and video input connectors on the
rear of your DVD-VCR, as indicated on page 14.
2
Insert a blank cassette in your DVD-VCR.
3
Insert the pre-recorded cassette in the other video source
(VCR or camcorder).
4
Press the INPUT SEL. button to select the appropriate input on
your DVD-VCR: LINE IN for the RCA input.
5
Start playing back the cassette to be copied.
6
Hold REC (
●
) down for a while to start recording on your
DVD-VCR.
7
When you have finished recording, press
■
on both VCR and
DVD-VCR.
➢
If you wish to view the cassette being copied:
◆
Your DVD-VCR must be connected as usual to the
television (see page 11 for further details)
OK
7
6
EJECT
AUX
2
VCR
VCR
VCR
00282A DVD-V530/XSA-GB2 8/18/03 2:27 PM Page 44
