background image

ENGLISH-3

01

 

PREP

AR
ATION

Safety Precautions

This installation manual explains how to install a ERV Wired Remote Controller connected to the indoor unit 

of your system air conditioner .
Please read this manual thoroughly before installing the product . 

(Please refer to appropriate installation for any optional product installation .) 

 WARNING

Hazards or unsafe practices that may result in 

severe personal injury or death

 .

 CAUTION

Hazards or unsafe practices that may result in 

minor personal injury or property 

damage

 .

 WARNING

Contact a service center for installation.

f

f

Potential risk of malfunction, water leak, electric shock and fire .

Install the product with proper power supply.

f

f

Potential risk of fire or product damage .

Consult the place of purchase or a contact center to disassemble or repair the product.

f

f

Potential risk of malfunction, electric shock, or fire .

The electric work must be done by qualified person according to national wiring regulations and 

installation guide.

f

f

If an unauthorized person performs the installation, any resulting defects can cause malfunctions, 

electrical shocks, or fire accidents . 

Install the product on a hard and even place that can support its weight.

f

f

If the place cannot support its weight, the product may fall down and it may cause product damage .

Do not move or reinstall the product on your discretion.

f

f

Potential risk of electric shock or fire .

Check if the installation work is done correctly according to the installation manual.

f

f

Incorrect installation may cause electric shock or fire .

When you want to dispose your Wired Remote Controller, ask the service center.

PREPARATION

ERV Wired remote controller_MWR_VH12N_IM_EN_05309A-00.indd   3

2016-12-23   오후 6:02:53

Summary of Contents for ERV























Reviews: