SAVE NUMBER WITH REDIAL
To save the number you just dialed for later use, press the
SNR
key before
hanging up.
To redial this saved number at any time, press the
SNR
key or dial
17
. The
same line will be selected for you.
NOTES:
1.
If the Hot Keypad feature has been turned off, you must first lift the hand-
set or press the
SPK
or
MONITOR
key if you are using 7B phone before
you begin dialing.
2.
The saved telephone number is stored in memory until you save anoth-
er number.
3.
Redial does not apply to intercom calls.
CHAIN DIALING
You may manually dial additional digits following a speed dial number or
chain as many speed dial numbers together as required:
•
After the first speed number is dialed, press
SPD
again and dial anoth-
er speed number
OR
manually dial additional digits following a speed
dial number.
AUTOMATIC REDIAL/RETRY
When you are making an outside call and you receive a busy signal, the sys-
tem can automatically redial the number for you. It will automatically redial
at a pre-programmed interval for up to 15 attempts.
•
When you hear a busy signal, press the
RETRY
button.
•
The system will reserve the line and automatically redial the same num-
ber for you. You will hear the call being made through the keyset speak-
er. The microphone is muted.
•
When the called party answers, lift the handset or press the flashing
SPK
to begin speaking.
NOTES:
1.
If you make another call, auto-redial is canceled.
2.
To cancel a retry, lift and replace the handset.
PULSE TO TONE CHANGEOVER
When making an outside call on a dial pulse line, press #. All digits dialed
after the # with be sent as tones.
27
For the purposes of programming speed dial numbers, the programmable
keys are known as
A
,
B
,
C
,
D
,
E
and
F
and are defined below.
•
The
A
key is not used.
•
The
B
key inserts a flash.
•
The
C
key inserts a pause.
•
The
D
key is used for pulse to tone conversion. If your system uses
rotary (or pulse) dialing C.O. lines, pressing
D
while entering a speed
dial number causes all subsequent digits to be sent as DTMF tones.
•
The
E
key is used to hide digits. Display keyset users may want to hide
some speed dial numbers so that they will not show in the display. When
you are entering a telephone number, press
E
. All subsequent digits will
be hidden. Press
E
again to begin displaying digits.
•
The
F
key is used to enter a name.
•
Use the
HOLD
key to clear a speed dial number.
ONE TOUCH SPEED DIALING
You may assign any speed dial number to an already existing One Touch
Speed Dial button for quick and easy dialing of frequently used numbers.
•
While on-hook, press
TRSF
and then dial
107
.
•
Press a One Touch Speed Dial button.
•
Dial the speed dial number (
00
–
49
or
500
–
999
) that you want assigned
to this button.
•
Press
TRSF
to store your selection.
To call this telephone number, just press the One Touch Speed Dial button.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the
handset or press the
SPK
or
MONITOR
key if you are using a 7B phone
before you begin dialing.
LAST NUMBER REDIAL
To redial the last telephone number you dialed, press the
LNR
key or dial
19
.
NOTES:
1.
If the Hot Keypad feature has been turned off, you must first lift the hand-
set or press the
SPK
or
MONITOR
key before you begin dialing.
2.
Redial does not apply to intercom calls.
26
HOME PAGE
Table of Contents
Guide-Contents
