English -
Listening through a Receiver (Home theater)
You can listen to sound through a receiver instead of the TV speaker.
1.
Press the
TOOLS
button. Press the �� or �� button to select “Receiver”.
2.
Press the �� or �� button to select to “On”.
Now you can listen to sound through the receiver.
3.
Press the
EXIT
button to exit.
If your receiver supports audio only, it may not appear in the device list.
The receiver will work when you have properly connected the Optical IN jack of the
receiver to the Optical Out jack of the TV.
When the receiver (home theater) is set to On, you can hear sound output from the
TV’s Optical jack. When the TV is displaying a DTV(air) signal, the TV will send out 5.1
channel sound to the Home theater receiver. When the source is a digital component
such as a DVD and is connected to the TV via HDMI, only 2 channel sound will be
heard from the Home Theater receiver.
When listening through the receiver, there are restrictions for using the audio-related (MTS, Preferred language)
menus.
If there is a power interruption to the TV when the “Receiver” is set to “On” (by disconnecting the power cord or a
power failure), the “TV Speaker” may be set to “Off” when you turn the TV on again. (see page 30)
➣
➣
➣
➣
➣
Troubleshooting for
Symptom
Solution
does not work.
Check if the device is an device. The system supports
devices only.
Connect only one receiver (home theater).
Check if the device power cord is properly connected.
Check the device’s Video/Audio/HDMI cable connections.
Check whether (HDMI-CEC) is set to On in the setup menu.
Check whether the TV remote control is in TV mode.
Check whether it is exclusive remote control.
doesn’t work in certain situations. (Searching channels, Plug & Play,
etc.)
When connecting or removing the HDMI cable, please make sure to search
devices again or turn your TV off and on again.
Check if the Function of device is set on.
•
•
•
•
•
•
•
•
•
•
I want to start .
Check if the device is properly connected to the TV and check if the
(HDMI-CEC) is set to On in the Setup menu.
Press the
TV/DTV
button on the TV remote control to switch to TV. Then press
the
TOOLS
button to show the menu and select a menu you want.
•
•
I want to exit .
Select View TV in the menu.
Press the
SOURCE
button on the TV remote control and select a device other
than devices.
Press
P
/ and
PRE-CH
to change the TV mode.
(Note that the channel button operates only when a tuner-embedded
device is not connected.)
•
•
•
The message Connecting to
device... appears on the
screen.
You cannot use the remote control when you are configuring Anynet
+ or
switching to a view mode.
Use the remote control when the setting or switching to view mode is
complete.
•
•
The device does not play.
You cannot use the play function when Plug & Play is in progress.
The connected device is not
displayed.
Check whether or not the device supports functions.
Check whether or not the HDMI cable is properly connected.
Check whether (HDMI-CEC) is set to On in the setup menu.
Search devices again.
You can connect an device using the HDMI cable only. Some HDMI
cables may not support functions.
If it is terminated by an abnormal situation such as disconnecting the HDMI cable
or power cord or a power failure, please repeat the device scan.
•
•
•
•
•
•
The TV program cannot be
recorded.
Check whether the antenna jack on the recording device is properly connected.
The TV sound is not output through
the receiver.
Connect the optical cable between TV and the receiver.
Tools
Device List
Record
Timer Recording
Receiver
�� Off ��
Picture Mode
: Standard
Sound Mode
:
Custom
Sleep Timer
:
Off
SRS TS XT
:
Off
��
e
Exit
Move
Adjust
BN68-01424E-02Eng-0514.indd 48
2008-05-15 ¿ÀÀü 9:34:30
