45
TROUBLESHOOTING
Descriptions of Self-Diagnosis Error Code
ERROR
CODE
ITEM
Description
How to do Self-Diagnosis
1 E
FREEZER
SENSOR
Connector Slipped-Out or Open-
Contact, Wire Cut or Short- Circuited,
Abnormal Sensing Temp (+50°C and over
or -50°C and lower).
The voltage should be within the range of
4.5V ~ 1.0V between MAIN PCB CN30 #3
and #7
2 E
FRIDGE
SENSOR
Same as the above
The voltage should be within the range of
4.5V ~ 1.0V between MAIN PCB CN30 #5
and #7
4 E
FREEZER
DEFROST
SENSOR
Same as the above
The voltage should be within the range of
4.5V ~ 1.0V between MAIN PCB CN30 #4
and #7
5 E
FRIDGE
DEFROST
SENSOR
Same as the above
The voltage should be within the range of
4.5V ~ 1.0V between MAIN PCB CN30 #6
and #7
6 E
AMBIENT
SENSOR
Same as the above
The voltage should be within the range of
4.5V ~ 1.0V between MAIN PCB CN30 #1
and #2
8 E
ICE
MAKER
SENSOR
Same as the above
The voltage should be within the range of
4.5V ~ 1.0V between MAIN PCB CN90 #3
and #8
13 E
HUMIDITY
SENSOR
Separation of sensor housing part,
contact error, disconnection, short circuit
The voltage should be within the range of
4.5V ~ 1.0V between MAIN PCB CN30 #7
and #9
21 E
FREEZER
FAN
ERROR
Bad Feed-Back Signaling Wire
Contact, Motor Wire Slipped-Out,
Defective Motor
The voltage should be 7V~12V between
MAIN PCB CN75 #1(GRAY) and
#4(YELLOW).
22 E
FRIDGE
FAN
ERROR
Same as the above
The voltage should be 7V~12V between
MAIN PCB CN75 #1(GRAY) and
#3(ORNAGE).
23 E
CONDENSER
FAN ERROR
Same as the above
The voltage should be 7V~12V between
MAIN PCB CN75 #1(GRAY) and #2(SKY
BLUE).
24 E
FREEZER
DEFROST
ERROR
Connector Slipped-Out or Open- Contact,
Wire Cut or Short- Circuited, Defective
Thermistor, or When it keeps heating during
Fridge Defrost even after it does defrosting
for 80 minutes.
After separating MAIN PCB CN70 wire from
PCB, resistance value between CN70
Brown
↔
Black(refer to the Circuit Diagram
for the resistance value) When it is 0 Ohm,
check if the Heater is short and when it is
Ohm, check if the wire or the thermal fuse is
open.
25 E
FRIDGE
DEFROST
ERROR
Connector Slipped-Out or Open- Contact,
Wire Cut or Short- Circuited, Defective
Thermistor, or When it keeps heating during
Fridge Defrost even after it does defrosting
for 80 minutes.
After separating MAIN PCB CN70 wire from
PCB, resistance value between CN70 White
↔
Black(refer to the Circuit Diagram for the
resistance value) When it is 0 Ohm, check if
the Heater is short and when it is Ohm,
check if the wire or the thermal fuse is open.
26 E
ICE
MAKER
FUNCTION
ERROR
I/M Ice Ejection Horizontal Positioning Error
** Only for Dispenser models
After replacing Ice-Maker, plug in the unit
and check its operation.
Summary of Contents for LS3165H52HR
