Samsung ME16K3000AS Installation Instructions Manual Download

Page: 7 / 24

General information

# 1 and #2

Phillips screwdriver

Pencil

Ruler or tape measure and

straight edge

Carpenter square (optional)

Tin snips (for cutting

damper, if required)

Scissors (to cut template, if

necessary)

Electric drill with

”, ½” and

” drill bits

Filler blocks or scrap wood

pieces, if needed for top

cabinet spacing (used on

recessed bottom cabinet

installations only)

Gloves

Saw

(saber, hole or keyhole)

Stud finder or Hammer

(optional)

Safety goggles

Level

Duct and masking tape

TOOLS YOU WILL NEED

16½”

30”

2”

30”min

Bottom edge of
cabinet needs
to be 30” or
more from
the cooking
surface

Backsplash

66” or More
from the Floor
to the Top of
the Microwave

NOTES:

• The space between the cabinets must be 30” wide

and free of obstructions.

• If the space between the cabinets is greater than

30”, a Filler Panel Kit may be used to fill in the gap
between the microwave oven and the cabinets.
Your Owner’s Manual contains the kit number for
your model.

• This microwave oven is for installation over ranges

up to 36” wide.

• If you are going to vent your microwave oven

to the outside, see Hood Exhaust Section for
exhaust duct preparation.

• When installing the microwave oven beneath

smooth, flat cabinets, be careful to follow the
instructions on the top cabinet template for
power cord clearance.

MOUNTING SPACE

DE68-03587B-EN.indd 7

2008-12-09 �� 4:13:04

Summary of Contents for ME16K3000AS

























Search results

Summary of Contents for ME16K3000AS

Reviews:

Related manuals for ME16K3000AS

Brands by name

Popular brands

Samsung ME16K3000AS, Installation Instructions Manual

Search results

Summary of Contents for ME16K3000AS

Reviews:

Related manuals for ME16K3000AS

Brands by name

Popular brands