Samsung MultiXpress K4 Series Service Manual Download | Manualshive

Page: 287 / 526

background image

4. Troubleshooting

4.5.5.5. Image Management

Auto Tone Adjustment Activation

•

Diagnostics > Image Management > Auto Tone Adjustment Activation > Normal

Purpose

To correct image quality when density of the image is poor. Normal TRC Control is recommended to
be performed after changing a unit, such as toner cartridge, imaging unit, and ITB, and reboot.

Operation Procedure

1) Select “On” or “Off” for Normal TRC Control execution.

•

If you select “Off”, Normal TRC Control will not execute.

•

If you select “On”, Normal TRC Control will execute as the determined conditions.

2) Change execution condition(s) of Normal TRC Control.

•

Page Count: The system executes Normal TRC Control based on the count of printed
pages since the last execution.

•

Time Left Alone: The system executes Normal TRC Control when the system returns
from a power save mode and the rest time exceeds the configured value.

Verification

Print out a test job and make sure the image quality has recovered.

•

Diagnostics > Image Management > Auto Tone Adjustment Activation > Full

Purpose

To correct image quality when any OPC drum is replaced or the life of the OPC drum is changed.
replacing any OPC drum or density of the image is poor. And this function will be performed when
temperature and/or humidity in the room changes suddenly.

Operation Procedure

1) Select “On” or “Off” for Full TRC Control execution.

•

If you select “Off”, Full TRC Control will not execute.

•

If you select “On”, Full TRC Control will execute as the determined conditions.

2) Change execution condition(s) of Full TRC Control.

•

Page Count: The system executes Full TRC Control based on the count of printed pages
since the last execution.

•

Time Left Alone: The system executes Full TRC Control when the system returns from
a power save mode and the rest time exceeds the configured value.

Verification

Print out a test job and make sure the image quality has recovered.

Copyright© 1995-2017 SAMSUNG. All rights reserved.

4-52

«
...
285
286
287
288
289
...
»

Summary of Contents for MultiXpress K4 Series















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MultiXpress K4 Series

Brand: Xerox Pages: 19

Brand: Canon Pages: 840

Brand: Toshiba Pages: 122

Brand: Toshiba Pages: 1

Brand: Toshiba Pages: 11

SmartLink e-STUDIO16

Brand: Toshiba Pages: 14

Brand: Toshiba Pages: 22

Brand: Toshiba Pages: 41

Brand: Toshiba Pages: 90

Brand: Toshiba Pages: 93

Brand: Toshiba Pages: 120

Brand: Toshiba Pages: 168

Brand: Olivetti Pages: 502

Brand: Canon Pages: 143

imageRUNNER ADVANCE C2030

Brand: Canon Pages: 14

Brand: Canon Pages: 55

Brand: Ricoh Pages: 12

Brand: Ricoh Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands